Diagnostics and repair of the Indesit washing machine if it freezes during rinsing or another stage of washing

Indesit washing machines are highly reliable and trouble-free.

However, even the highest quality equipment breaks down over time, especially since modern units are filled with electronics.

Read the article about what to do if the Indesit washing machine freezes during washing, spinning or rinsing.

What to do first?

If a properly working Indesit machine suddenly starts to freeze while performing operations, there is no need to panic. Sometimes the slowdown in the operation of the device is not associated with a breakdown.

If a problem is detected, the priority actions should be as follows:

1. Rebooting equipment. To do this, you need to hold the “Start” button for a few seconds. The running program must stop. If you cannot reset it, you must move the programmer knob to the neutral position and hold the “Stop/Start” button for 5 seconds. Then unplug the cord from the outlet and leave the device turned off for 15 minutes, then turn it on again.
2. Check if the laundry is bunched up. If there is a serious imbalance, the machine may stop.If this really happens, you need to lay out the laundry manually, or divide it into 2 parts and spin them alternately.
3. Check the specified program. There are options that do not involve spinning and draining water from the tank. In this case, they must be turned on forcibly.

If none of these problems were found, you need to look for other reasons for the washing machine freezing.

Why did it freeze during the washing process?

Reasons that may cause the washing machine to freeze during washing:

Problems with water collection

There are many reasons why this could happen.

The most common of them:

• lack of water in the tap,
• shutting off the water valve,
• pinched or clogged hose,
• dirt getting into the water supply valve or its malfunction,
• control module failure,
• malfunction of the hatch locking device.

All these factors will lead to the equipment freezing at the initial stage of washing. If a blockage is found in the hose or valve, they need to be cleaned. If faulty parts are found, they must be replaced.

Breakdown of the pressure switch

If the water level sensor fails, the control board stops receiving signals and stops the washing process. Broken part must be replaced.

Checking the pressure switch is easy. It is located under the top cover of the washing machine. It needs to be removed, unscrew the bolts holding the part and inspect for blockages.

Then you need to blow into the tube. If you hear a click, the sensor is working. No sound indicates that it needs to be replaced. Read about troubleshooting pressure switch failures in this article.

Electric heater malfunction

If the heating element in a washing machine breaks down, it cannot heat the water.The control board is waiting for the liquid inside the drum to reach the desired temperature. Since this cannot happen, the wash stops.

Such the situation requires a forced stop of the device and replacement of the electric heater. In Indesit washing machines it is located under the tank. To gain access to it, you must remove the back cover. The heating element is attached to self-tapping screws that are unscrewed. A new part is inserted into the vacated slot.

Instructions for replacing the heating element in a washing machine are presented in this article.

The brushes are worn out

This problem is relevant for commutator engines. Brushes wear out during prolonged or excessive use.

If their length is less than 1 cm, they cease to perform their function. As a result, the drum simply stops rotating during washing.

To restore the operation of the device, it is necessary to dismantle the engine, disassemble it and replace the broken brushes.

Foreign object stuck between tank and drum

A bra wire or other small parts can cause the wash to stop. To understand that the reason for the machine freezing lies precisely in this, a forced stop of the wash and draining the water will help. Then you need to try to spin the drum. If it stands still or turns but with force, it needs to be disassembled.

Violations at the water drainage stage

There may be several reasons:

• clog in the area of ​​the drain filter or pipe,
• pump malfunction,
• failure of the pressure switch or control module.

The blockage is removed by cleaning the parts, and broken components are replaced.

Failure of the control board

It can fail for various reasons, but the most common of them is a voltage drop in the network. If a software failure occurs, the machine will freeze during the washing process.

The video will tell you about repairing the control module:

The motor is broken

It may fail during long-term use or due to exposure to water.. If the motor burns out, the device will simply stop the wash.

You can repair or replace the motor yourself. It is located at the bottom of the machine. To access it, you need to unscrew the back wall of the case. Further actions depend on the condition of the part.

Reasons why the Indesit washing machine freezes during rinsing and spinning

The reasons why the Indesit washing machine may freeze during rinsing or spinning often overlap with those that lead to it stopping at the washing stage. These include:

1. Sensor failure, which controls the balance of the laundry (it is not available in all models).

   If the device is equipped with this component and it fails, the spin cycle will not start, since the control board will not receive a signal that all systems are working.

   If the sensor breaks, it will have to be replaced. Most often it is located in one of the shock absorbers.

2. Shock absorber failure. They fail due to excessive vibration or prolonged use of the device. It's easy to replace it yourself. However, if one shock absorber breaks down, the second part will also have to be replaced.
3. Tachometer failureresponsible for speed control.If it fails, the control board cannot understand what the spin speed is, so it stops the process. A part needs to be replaced. The tachometer is located on the motor shaft. To get to it, you will have to remove the back cover of the washing machine.

Reasons that can lead to freezing washing machine during spinning and rinsing, as well as during washing (methods for eliminating them were described above):

• failure of the pressure switch - the water level sensor is located under the cover;
• disturbances in the functioning of the water drainage system;
• control board failure.

Call the master

If you cannot repair your washing machine on your own, you need to seek help from a specialist.

There are several ways to find a master:

1. Contact the service center.
2. Find an advertisement in the newspaper.
3. View advertisements on the Internet on specialized websites.
4. Take advantage of word of mouth.

To avoid meeting a scammer, You need to study in advance the approximate prices for different types of repairs:

• cleaning the blockage, replacing the water supply valve - from 600 rubles;
• repair of the pressure switch – 1500 rubles;
• replacement of brushes – from 1400 rubles;
• removal of a foreign object between the tank and the drum - from 600 rubles;
• pump replacement – ​​from 1500 rubles;
• repair of the control board – from 2400 rubles;
• replacement of the balance sensor – from 900 rubles.

The price does not include the price of the part. If repairs of spare parts are required, they are paid separately. An honest master will warn you in advance about how much his services will cost, so that the final payment does not become an unpleasant surprise for the client.

A lot of important and useful information about the repair of Indesit washing machines is presented in this section.

Conclusion

If the machine freezes while performing one of the operations, you should not panic. First you need to try rebooting it. If after this procedure the unit’s performance has not been restored, proceed to more thorough diagnostics.

You can deal with minor breakdowns on your own. For complex repairs, you will need to hire a specialist.