Step-by-step instructions for repairing the shock absorber of an Indesit washing machine with your own hands
Systematic overloading of the tank, lack of balancing when installing an Indesit washing machine, damages one of the important elements of the internal structure - the shock absorber.
It is this small part (or rather a pair of elements) that dampens the strongest vibration inside the washing machine that occurs during the rotation of the drum.
Failure to promptly replace worn shock absorbers can cause serious damage. The thing is that during the washing or spinning process, the drum hits the body of the washing machine, violating the integrity of adjacent components and mechanisms.
Monitoring the condition of shock absorbers and replacing them in a timely manner if wear is suspected will help prevent household appliances from falling apart.
We will tell you in this article how to repair the shock absorber of an Indesit washing machine with your own hands.
Content
How to check whether the element can be repaired or needs replacement?
It is very simple to determine whether the shock absorber in an Indesit washing machine needs to be replaced.
For this it is necessary to perform a number of sequential actions:
- Remove the top cover of the washer.
- It is enough to press firmly on the tank so that it moves at least 5 cm, and then release your hands.
If, after pressing, the tank rises sharply and locks in one position, the shock absorbers do not require replacement.If the tank begins to swing in different directions after pressing, the washing machine must be repaired.
Additionally, shock absorbers are tested for performance after disassembling the washing machine. The part is compressed. If compression occurs with force, the part does not require replacement. If the piston moves with the slightest pressure, then the shock absorber requires replacement.
Depending on the model, the Indesit washing machine can be equipped with collapsible or solid shock absorbers (the type of part can be determined only after dismantling it).
How to remove the part?
The hum and strong vibration of the washing machine during the washing process indicate that the shock absorbers need to be replaced.
You can remove the worn part, adhering to a certain algorithm of actions:
- Disconnect the washing machine from the power supply, water supply and sewerage.
- Pull the washing machine away from the wall and place it on a flat surface (if possible, it is better to take the household appliance out of the bathroom and into the utility room during repairs).
- Unscrew the two bolts securing the top panel.
- Unscrew the drain filter, drain the remaining water, and remove the washing powder tray.
- Unscrew the fixing bolts and remove the back panel.
- Carefully turning the pulley, remove the drive belt.
- Disconnect all wires from the engine.
- Loosen the fastenings holding the motor.
- Using a flat-head screwdriver, use a flat-head screwdriver to pinch the motor and then pull it out of the housing.
- Carefully lay the washing machine on its side and begin dismantling the shock absorbers
Dismantling shock absorbers on an Indesit washing machine has one very important feature - plug fastenings (popularly called “nails”). Absolutely smooth fastenings firmly fix the shock absorbers to the body and tank of the washing machine. It will not be possible to knock out such “nails” with a regular hammer.
To remove a worn part, you need to do the following:
- Use a long drill (diameter 2-2.5 mm) to drill a through hole in the “nail” fastening;
- screw a self-tapping screw into the hole, leaving 3-4 cm unscrewed;
- Grab the self-tapping screw with pliers and pull the “nail” fastener out of the seat;
- remove the shock absorber from the grooves.
After the new part is installed and the “nail” fastening is restored to its original place, the self-tapping screw is unscrewed.
How to replace?
Installation of new shock absorbers carried out according to the following algorithm:
- We place the new element in place of the removed part, in special grooves.
- Carefully screw in the “nail” fastener and remove the self-tapping screw from it.
- Turning the washing machine over to the other side, repeat the steps.
The assembled machine is returned to its original location and connected to the water supply and sewerage system. The device is connected to the network.
The final stage is verification. To do this, start the wash at maximum spin mode. If during the process the washing machine does not shake much (moderate vibration is acceptable) and does not change its location, then the repair is completed successfully.
The video will show you how to change shock absorbers on an Indesit washing machine:
We fix the problem ourselves
Repairing the shock absorber yourself will help you save money on purchasing new parts. Restoring the functionality of an old part is possible in the event of abrasion of the liner or gasket. Mechanical damage (distortion, cracks) requires complete replacement of the part.
How to change gaskets or liners?
Light, fast movement of the rod when compressing the shock absorber indicates that the gasket has worn out. It's easy to replace it It is enough to adhere to a clear algorithm of actions:
We measure the diameter of the sleeve hole (use a caliper).- Based on the measurements, we cut off a piece of rubber (thickness of at least 3 mm; alternatively, you can use a brake pad or a piece of PCB).
- We insert the cut piece into the place of the previously worn out seal (the edges of the new gasket should meet).
- Lubricate the part and install the shock absorber rod in its original place.
Lubricate the new part immediately before installing the rod. It is important to use lubricating oils that are resistant to moisture, resistant to high temperatures, and have a high viscosity index.
Where to buy a shock absorber for an Indesit washing machine, at what price, how to choose?
When choosing a new set of shock absorbers, you need to pay attention to the following points:
- length (in compressed and open form must correspond to the parameters of the dismantled element);
- bushing diameter (even a slight deviation from the original parameters of the dismantled element will not allow a high-quality installation of a new shock absorber);
- load indicator (indicated by the manufacturer on the case, varies from 100N to 150 N);
- shock absorber stiffness (the parameter is indicated by the manufacturer on the body, most often designated as 85N or 80N).
When going to the store, it’s a good idea to take an old part with you as a sample. This will help avoid selection mistakes.
The cost of a pair of shock absorbers varies from 450 rubles. up to 1500 rub.
How much does a master's service cost?
A professional technician can quickly solve the problem of failed parts. service center. On the Internet it is not difficult to find the coordinates of companies servicing Indesit equipment.
When filling out an application, you must indicate the brand and model of the washing machine, describe the problem in detail, and agree on the time of the technician’s arrival.
The cost of the service is determined by a number of factors:
- Efficiency of order fulfillment (additional payment for urgency is possible).
- Model and production date of the washing machine (determines the difficulty of disassembly).
- The cost of a new spare part (the original part is more expensive).
The repair estimate usually includes:
- disassembling the washing machine,
- dismantling old and installing new shock absorbers,
- assembly and testing of equipment after repair.
The specialist will announce the full cost of repair work only after inspecting the household appliances and fully diagnosing the fault. Demanding full payment even before the start of repairs is a reason to refuse the services of a specialist (the risks of fraud are high).
It is also necessary to remember that, after repair The service center master is obliged to issue a document - Certificate of completion of work with a full list and cost of services provided, a guarantee for the replaced part.
The average cost of replacing a pair of shock absorbers in an Indesit washing machine is 2,200 rubles.
A lot of important and useful information about the repair of Indesit washing machines is presented in this section.
Conclusion
The process of replacing shock absorbers in an Indesit washing machine is not particularly difficult. Success is guaranteed if you carefully study the theoretical part of the process in advance, choose the right new part.
