Instructions for replacing the drive belt for an Indesit washing machine

The belt in the Indesit washing machine is the part that ensures the rotation of the drum. If it fails, washing cannot be performed.

Failure information appears on the display and may be accompanied by extraneous sounds.

Why the Indesit washing machine belt becomes unusable, how to replace it, where to buy a part for the washing machine, we will tell you in the article.

10 reasons why a part becomes unusable or falls off

To rotate the washing machine drum, a metal pulley is installed and secured to it. Another pulley with a much smaller diameter is mounted on the engine.

But sometimes it can fly off the pulley or even break. The following factors can lead to this:

1. Operation under increased loads not provided for this model. If the jumping off occurs for the first time, the part can be returned to the pulley and continue to use the washing machine.

   This situation may occur, for example, when the washing machine was unable to evenly distribute the laundry before performing an intensive spin.

   As a result, the amplitude of the tank's movement increases, which can cause it to fly off.

2. The belt breaks if the machine is not used for a long time. Significant breaks in work lead to drying out of the material and loss of elasticity. Such a part, when loaded, stretches and breaks.
3. Worn bearings can affect the position of the drum as it rotates. If a misalignment occurs and high vibration is created, the part connecting the pulleys may weaken and fly off. In this case, repair of the bearings is necessary, since otherwise the situation with the belt will repeat.
4. The shaft is connected to the body using a cross. If it has defects, this can cause the part connecting the two pulleys to fly off. In such a situation, it is first necessary to resolve the issue specifically in relation to the cross.
5. Deformation (breakage) of the pulley or axle can cause the belt to fly off. To resolve the issue, it is important to analyze the condition of the parts and replace them if necessary.
6. A loose pulley that is not securely fixed can also cause it to fly off. To prevent the situation from repeating, it is necessary to restore its normal position.
7. A loose motor can also cause the belt to slip off. Reliably fixing the position of the motor in the washing machine body will help solve the problem.
8. Operation at high speeds can cause the belt to jump off the pulley. If the situation is one-time, the existing part is simply returned to its place, but if it comes off again, it is advisable to replace it.
9. In narrow Indesit models, as a result of vibrations, there may be friction between the device elements and the body, which increases the degree of wear. This is due to the very close arrangement of the parts both to each other and to the housing, which affects the wear rate of the components, including the drive belt.
10. If the washing machine lasts 5-6 years or even more, the belt may become unusable as a result of natural wear and tear. This is a normal situation that requires replacement of the part.

• displaying an error code on the display;
• stopping the rotation of the drum or its slow movement, accompanied by extraneous sounds.

Troubleshooting

To organize the normal operation of the Indesit washing machine, it is necessary to install the belt on the pulley. This kind of work can only be done when communications are turned off. You should also drain the remaining water from the device through the emergency drain.

How to get to the belt in an Indesit washing machine with vertical and horizontal loading?

The ability to gain access to the drive belt depends on the model of the Indesit machine.

In front-loading devices, it is organized from the rear wall. To replace a part, you need to pull out the washing machine and remove the service hatch cover, which is located at the back. The cover is secured with screws.

In Indesit top-loading machines, the belt can be accessed by removing the side panel. To do this, you need to unscrew all the screws holding it.

How to change, tighten?

After access to the pulley and belt has been gained, the entire assembly should be inspected, paying attention to the secure fastening of all parts involved in rotating the drum. If the cause of the part jumping off has been established, it must be eliminated first.

Installation process:

1. Inspect the old belt, checking its condition and integrity. If it is torn or has become dilapidated, it should not be mounted on the pulley.This part cannot be repaired - only replaced.
2. Inspect the condition of the parts and components associated with the belt. If a defect is identified, it must be eliminated before installing a new belt.
3. Throw the new part onto the electric motor pulley, which is located below.
4. How to put a belt on a large pulley that is located on the drum - it is more convenient to do this by spinning the wheel. To work, you need to use both hands - one to pull the part, and the other to spin the wheel.
5. Checking the installation.

The video will tell you about replacing the belt in an Indesit horizontal-loading washing machine:

Video about replacing the belt in a top-loading Indesit washing machine:

Reassembly

After installing the belt, it is necessary to restore the position of the removed housing panel. And only after this can the communications connection be restored. The replacement is completed by a test run without loading laundry..

Rules for selection and purchase

The drive belt is a part that should not be bought by eye. When purchasing it at a specialized retail outlet, you must indicate the brand of washing machine and model in order to select the correct part. But you can go another way.

You can also order the part on the Internet, based on the information that is on the damaged belt.

Important selection parameters are:

• belt type;
• belt length.

The following types of belts can be used in Indesit washing machines:

1. Half-wedge – for devices with a commutator motor.
2. Wedge – for devices with an asynchronous motor.

The average price for belts for an Indesit washing machine ranges from 250 to 1,500 rubles.

Call the master

You don't have to replace the belt yourself. To carry out work, you can contact the company, which repairs washing equipment.

Finding such companies is not difficult on the Internet. The websites of service companies provide contact information and, most often, a price list. It is more convenient to discuss the conditions for calling a specialist and all the details with the dispatcher by phone.

Please indicate:

• brand of washing machine;
• washing machine model;
• Is there a new part to replace the one that has become unusable?

The cost of a technician’s services may vary depending on the complexity of the task, if, for example, it is necessary not only to replace the belt, but also to carry out additional repair work. On average, the price for replacing a belt in the capital is from 1,000 rubles.

Measures to prevent element wear

In order to avoid the problem of a flying or torn belt in the Indesit washing machine, It is recommended to take into account the following tips:

1. Avoid overloading the drum. But it is better not to send one item into the wash, as this leads to an imbalance in the arrangement of the laundry and contributes to faster wear of parts, including the belt.
2. If unusual sounds appear, you need to turn off the device and find the cause of the problem.
3. It is necessary to transport the machine with transport bolts, which are removed after installation.
4. Violation of the speed of rotation of the drum and extraneous sounds are a reason to carry out diagnostics.
5. If a burning smell appears, the machine must be turned off immediately.

Do not attempt to repair a broken drive belt.

A lot of important and useful information about the repair of Indesit washing machines is presented in this section.

Conclusion

The washing machine belt is an important part that ensures the rotation of the entire drum. As a result of the work it can wear out, tear and fly off.

You can even restore the operation of the Indesit washing machine yourself by replacing the damaged part with a new one. If you can’t do the work yourself, you can call a technician at a convenient time who will carry out the replacement quickly and efficiently.