Why does the Indesit washing machine make noise when spinning, what should I do about it?
The Indesit automatic washing machine does not always work quietly. Usually noise occurs during the spin phase, and this very often indicates a breakdown.
If you hear alarming sounds, you need to carry out diagnostics to determine the causes of the unusual sounds.
The reasons for the noise of the Indesit washing machine during the spin cycle, why the device rattles and vibrates, troubleshooting methods are discussed in the article.
Content
It makes a lot of noise - is this a breakdown or normal?
During operation of the device, noise may sometimes even be a normal situation. Some sounds that Indesit makes are not a sign of failure.
Such situations include noise in the following processes:
- water inlet;
- pump operation;
- heating water;
- rotation of the drum during the spin process;
- clattering transition to a new stage of the washing program.
You should start to worry when the car suddenly starts making strange sounds that are not typical for it. Most often, they make themselves felt precisely when the drum is actively rotating and under high load. If there is noise in the device, it is important to correctly determine its cause.
In some cases, such a sign is not a breakdown. Each device has a maximum permissible noise value.
Causes and solutions
If you detect unusual sounds during spinning Indesit, which are not typical for the normal operation of the device, you must determine the source of the malfunction. The reason could be any - from improper installation of the device and negligence when storing laundry to serious breakdowns.
In a new and just transported washing machine
If the device begins to make noise after transportation, it is necessary to clarify whether the transport bolts have been removed.
They are attached to the back wall of the household appliance and are needed to prevent the drum from loosening during transportation. But when the car is installed in a new place, they must be removed.
There may also be noise during the spin cycle, if the following circumstances occur:
- The device is installed on an uneven surface.
- When the drum rotates intensively, the back or side wall hits the wall or nearby pieces of furniture.
- The floor surface is too slippery.
It is recommended to keep the shipping bolts, as well as the instructions for the washing machine, for the entire time you use the washing machine.
Underload and overload
Noise at high speeds can indicate both an overload of the drum and a strong underload when, for example, only one T-shirt was sent for washing.
During operation, Indesit cannot properly distribute the laundry, which affects the appearance of noise. The solution to the problem is monitoring the load of laundry.
Foreign objects
If you hear a buzzing and grinding sound when spinning clothes, then there is a possibility that foreign objects from your clothing pockets have accidentally entered the machine.In this case, coins, paper clips and other things can not only linger in the drum, but also get into the tank.
The danger of such a situation is possible serious damage to the tank, heating element and other details. While the washing stage is in progress, the rotation of the drum is not as intense as during the spin cycle, so the presence of a foreign object may not appear in any way.
It is important that after removing the item from the tank, perform all the work in the reverse order carefully and accurately. According to statistics, objects accidentally falling into the car are one of the most common causes of noise.
Bearing wear
This problem is typical for Indesit washing machines that have been in use for a long time.
During operation of the device Over time, the seal begins to lose its tightness. In this case, water gets into the bearings, which eventually rust and collapse.
If you ignore such a breakdown, the situation may worsen: the spin cycle is no longer sufficient, the laundry may have rust stains on it after washing, and leaks and breakage of other parts are also possible. The solution to the problem is timely replacement of the oil seal and bearings.
The work of replacing bearings is quite complex, and if you lack the skills, it is better to entrust it to professionals. You can find out how to change bearings here.
Shock absorbers are worn out
Significant vibration and loud knocking when spinning may indicate wear on the shock absorbers. In a situation where the wear is significant, the washing machine may not only make noise, but also bounce.
The solution to the problem is to replace parts.Moreover, it is necessary to replace shock absorbers in pairs, even if signs of wear are noticeable on only one. Will tell you how to change shock absorbers this article.
Problems with the pump
When spinning the Indesit machine, the pump is activated. The noise can indicate not only wear of the part, but also the entry of a foreign object into the pump. Diagnostics can be carried out by partially disassembling the device.
The engine broke down
If the engine breaks down, it may make noise and crackling noises during spin cycles when the load on it increases. The electric motor brushes are responsible for the torque. If they become unusable, they need to be replaced.
Counterweight malfunction
The malfunction of the counterweight is especially noticeable when the drum rotates intensely - during spinning. If this happens, the car rattles and vibrates a lot.
The situation can be corrected after analyzing the state of the counterweight. If it becomes loose and moves away from the fastenings, it is secured.
But in cases where the counterweight is destroyed, it is replaced with a new one.
Loose drum pulley
As a result of using the washing machine The drum pulley may become loose. In this case, when spinning, the pulley dangles and creates a rumble. There may also be some noise when washing, but not as much. Solution to the issue: if the nut is loose, it needs to be tightened.
Loose noise filter fastener
If the noise filter fastenings are loose, the noise during the spin cycle may come from the top of the washing machine. You can verify the condition of the filter by partially disassembling the device. The solution to the problem is to tighten the fasteners.
Elimination of extraneous noise in the Indesit washing machine - in the video:
Prevention measures
In order not to encounter the problem of noise during the spinning process of the Indesit washing machine, It is necessary to remember the following preventive measures:
- When stowing items, be sure to check the pockets of items and not stow underwear with poorly sewn buttons, decor, etc.
- The search for the source of the problem should begin with simple nodes, gradually moving to complex ones.
- If extraneous sounds appear in the “spin” mode, it is necessary to organize diagnostics and establish the cause of the problem.
- It is advisable to start the machine with optimal load of laundry. It is better to avoid overloading and underloading.
- The service life of a household appliance without breakdowns largely depends on the correct installation and connection of communications.
A lot of important and useful information about the repair of Indesit washing machines is presented in this section.
Conclusion
Noise in the Indesit washing machine during spinning requires a mandatory search for the cause of unusual sounds. If worn parts and other defects are detected, it is necessary to repair the worn unit.
But not all breakdowns can be identified and repaired on your own.. If it is difficult to do this yourself, you need to call a technician from a washing machine repair company.
