Why doesn’t the Indesit machine take in water, what should I do about it?

Indesit washing machines are in high demand among customers, which is due to the affordable cost of the devices and the positive reputation of the brand. However, even the most reliable equipment is not immune to breakdowns.

If, after starting the wash, the Indesit machine does not draw water, you need to look for the cause of the problem and ways to solve it. This and more will be discussed in the article.

Causes

If, when you try to start the washing process, the drum of the Indesit washing machine remains motionless, most likely some kind of breakdown has occurred. Although first you need to make sure that water flows into the device at all.

Priority actions:

1. Check if there is water in the tap. Perhaps its supply is simply turned off throughout the house.
2. Is the water supply valve, if installed, open? Sometimes it is accidentally blocked by pets or children.
3. Are there any problems with the hose responsible for the water supply: is it kinked, are there any heavy objects on it, etc.
4. The hatch door is not pressed tightly. Until the lock icon (closed padlock) appears on the screen, the wash will not start.

If none of these factors are detected, something has happened to the appliance itself. Reasons that lead to malfunctions:

• the water supply valve is clogged or broken;
• the control module has failed;
• the pressure switch responsible for controlling the water level has broken down - it does not fill up due to the fact that the device does not understand whether liquid has entered the drum or not;
• the hatch locking device is broken;
• the pump burned out.

Diagnostics

To understand exactly what reason led to the fact that the Indesit washing machine does not take in water, you need to know the basic principles of diagnosis:

1. A clogged inlet valve occurs due to small debris that is periodically found in tap water. To prevent it from getting into the washing machine, the entrance to the valve is blocked with a fine mesh, which needs to be inspected. If there is no blockage in the mesh area, you need to check the serviceability of the valve itself. Error code - H20.
2. If the breakdown is reduced to a malfunction of the control module, then the machine will not draw water, since it does not receive this command. It is difficult to independently understand that it is the control board that is faulty. The error code is F18.
3. The fact that the water level sensor has failed will be indicated by error code F04. It’s easy to check the pressure switch for functionality yourself. It is removed and blown into a tube. If you hear clicks, the part is working. No sound indicates a breakdown.
4. If the hatch lock does not work, the lock icon will always light up on the display. The machine will not start washing if there is no way to lock the door. A faulty UBL is indicated by error code F17.
5. If the pump burns out, a signal will be transmitted to the control board that the machine cannot drain water. In this case, the smart equipment will not start the wash cycle, which is why liquid will not be collected. Error code - F05.

Troubleshooting methods for Indesit washing machine

If the Indesit washing machine is under warranty, then if it breaks down, you need to contact a service center. Our specialists will independently diagnose and repair the equipment. It is important that the body of the machine has not been previously opened. Otherwise, the warranty on it is void.

If trivial reasons such as a water outage, loose sealing of the hatch door or a closed inlet valve are excluded, you will have to systematically check all the components that could have failed. Experts recommend starting with the simplest details, gradually moving on to complex components.

Breakdown of the pressure switch

A failed pressure switch will send a signal to the control board that the tank is full, although water is not being filled into it.

If you find out that the water level sensor is broken, it will have to be replaced. It is located immediately under the top cover of the case, so it’s not difficult to get to it on your own.

After removing the faulty pressure switch, a new part is installed in its place. It can be purchased online. The price starts from 900 rubles, the exact cost depends on the model of the device. Read about the breakdown of the pressure switch of the Indesit washing machine in this article.

Input filter clogged

Before you start cleaning the valve, you should check for blockages in the hose through which water enters the machine. It is disconnected and washed under running water.

If it passes freely, proceed to processing the valve mesh:

• disconnect the hose;
• find a mesh on the valve;
• use pliers to remove it, holding onto a small protrusion;
• clean the mesh from blockages - for convenience, you can use a needle or toothpick;
• rinse it under running water and put it back in place.

Then they proceed to washing the deep cleaning filter.

Treatment and replacement of the water supply valve

If the valve fails, it cannot be repaired; the part will need to be replaced. The procedure is as follows:

1. Disconnect the hose from the machine and drain the remaining water.
2. Remove the top housing cover.
3. Disconnect the connectors on the coil.
4. Using pliers, loosen the terminals to remove the hoses.
5. Loosen the screws that hold the valve and remove it.
6. A new part is installed in its place.
7. Reassemble the machine in reverse order.

Board failure

Sometimes the reason that the Indesit machine does not take in water is a malfunction of the control board. If all other failures are excluded, you can try to reboot it. However, they resort to this measure in emergency cases.

Proceed as follows:

• set the programmer knob to the neutral position;
• hold down the “Start/Start” button for 5 seconds;
• disconnect the device from the network and leave it for 20 minutes;
• reconnect the machine and check its functionality.

If this measure does not help to cope with the breakdown, it is better to contact a specialist. Replacement and control board repair – a complex process that requires certain knowledge and skills.

Burnt out pump

It is difficult to replace a burnt-out drain pump yourself, since you will have to get to it through the bottom of the machine.

Procedure:

1. Unscrew or open the panel located at the bottom of the device.
2. Find the pump and tighten the bolts that secure it.
3. Disconnect the wires and pipes.
4. Install a new part and reassemble the machine in the reverse order.

Call the master

If you have no experience in repairing household appliances, it is better to entrust this work to a specialist. On the Internet you can find many advertisements from craftsmen offering their services. It is better to choose an expert who has many positive reviews or cooperates with a service center.

Repair cost depends on which part needs to be replaced:

• replacement of the water supply valve – 1100 rubles;
• flashing or replacing the control module – from 1,500 rubles;
• replacement of the pressure switch – from 1300 rubles;
• replacement of the hatch locking device – from 1400 rubles.

Fault prevention

To prevent clogging of the main parts, the Indesit washing machine must be periodically descaled. Citric acid is used for this. It, in the amount of 5 sachets, is poured into the powder compartment and the washing mode is turned on at the highest temperature. This procedure must be repeated once every six months.

All parts will last longer if the device is operated according to the instructions.. You need to install it on a flat surface, avoid overloading, and keep it clean.

A lot of important and useful information about the repair of Indesit washing machines is presented in this section.

Video on the topic of the article

Why the washing machine does not fill with water and how to fix the problem, the video will tell you:

Conclusion

There are several reasons why the Indesit washing machine does not fill with water.Some of them can be eliminated on your own, others require contacting a specialist. If you are not sure that you will be able to cope with the breakdown on your own, it is better not to skimp on the services of a specialist.