Why does the Indesit washing machine display error F05, how to find and fix the problem?

When operating the Indesit washing machine, a breakdown may occur in the drainage system, resulting in error F05.

In such a situation, it is impossible to continue washing without fixing the problem.

What to do if the Indesit washing machine shows error code F05, we will tell you in the article.

The Indesit washing machine shows code F05 - what does this mean?

F05 appears on the machine display indicates a water drainage problem. Signs of a problem are a stop in operation - rinsing and spinning are not performed.

To eliminate the problem, you need high-quality diagnostics and determination of the reason why draining water has become impossible.

Causes and diagnosis

The appearance of F05 on the display does not always indicate a serious breakdown of the device. In some cases, the problem lies in poor care of the machine.

Reasons for the impossibility of draining:

• breakdown of the pressure switch;
• pump failure;
• clogged sewer system;
• clogged drain hose;
• filter contamination.

In rare cases in autumn, the reason for the lack of drainage may be a breakdown of the control module.

Sometimes the appearance of F05 is a system failure, which a reboot will help resolve. Do it as follows:

1. Turn off the power by pressing the on/off button.
2. Remove the plug from the socket.
3. Leave the machine turned off for 20-30 minutes.
4. Connect the device to the mains.
5. Press the power button on the washing machine body.
6. Run a short wash cycle without adding laundry or washing powder.

Sewer blockage

If the sewage system of an apartment or house is clogged, it will be difficult to drain water not only from the washing machine, but also from the sink and bathtub. You can clean the sewer pipes either yourself (for example, with a special plumbing cable) or by calling a plumber.

To make sure the problem is not with the washing machine, you can do the following:

• disconnect the washing machine from the power supply;
• disconnect the drain hose from the sewer connection, if possible;
• throw the free end of the hose into the sink or bathtub;
• connect the washing machine to the mains;
• select the “drain” mode;
• if water flows from the hose, we can conclude that the problem lies not in the washing machine, but in a clogged sewer;
• clean the sewer system;
• install the free end of the drain hose of the machine in the same place where it was inserted into the pipe.

Otherwise, if error code F05 still appears, you need to proceed with sequential diagnostics of the functionality of the washing machine. It is advisable to start with units that are easier to access and repair, and then move on to complex ones.

The drain filter and hose are clogged

The drain filter in the washing machine is designed to catch small foreign objects that have fallen into the drum. These could be threads, torn buttons, coins, etc.

Procedure:

1. Open the panel from below, on the front side of the machine.
2. To remove the filter, you need to turn it from left to right and pull it towards you.
3. Clean the filter manually.
4. Return everything to its previous state.

To prevent this situation from occurring, the filter should be cleaned regularly.

The procedure for removing and cleaning the drain hose can be seen in the video:

Breakdown of the pressure switch

If there is no sewer blockage, the drain filter is not clogged, the reason for the malfunction of the Indesit washing machine may be a malfunction of the pressure switch or pump.

Diagnosis of the condition of the unit should be carried out when communications are disconnected, without power, and after draining the water.

Procedure:

• remove the top cover;
• inspect the part for damage, reliability of contacts, etc.;
• disconnect and inspect the supply tube - any deformation can cause error F05 to appear;
• the removed part should be tested using a multimeter in resistance test mode;
• If there are burnt areas of contacts on the body, it is recommended to replace the sensor.

Inspecting this unit is a more difficult job than cleaning the filter, so if you do not have the skills to work with equipment, entrust the diagnosis and repair to a specialist.

Pump malfunction

A pump that has become unusable is one of the most common reasons leading to F05. The pump is a pump, it is located at the bottom of the Indesit washing machine.

Work order:

1. Disconnect the washing machine from communications.
2. Drain the water.
3. Carefully place the washing machine on its left side.
4. Disconnect the pump from the wires and pipes.
5. Check the functionality of the impeller - it should turn without effort.
6. Make sure there are no external defects on the part.
7. Check the condition of the contacts and clean them if necessary.
8. Clean the pump. To do this, unscrew the screws that connect the two halves of the part.
9. Connect the elements of the pump and return it to its place, connecting the pipes and wires.
10. Check the connections are secure.

It is advisable to combine cleaning the pump with cleaning the supply pipes.

You can see how to deal with the problem in the video:

Electronic control module failure

The control module has a complex organization. Various factors can affect its operation - from condensation on the surface to burnt-out board elements. If the surface of the board is wet, it should be dried, as this defect can cause short circuits.

Failure may be indicated by melting of element bodies, dark spots and other external defects. But it is better to entrust full-fledged comprehensive diagnostics and repair of this unit to professionals.

Call the master

In cases where the decision is made to call a specialist, you need to find a company that specializes in repairing household appliances, in particular – Indesit washing machines. Such companies can easily be found on the Internet.

The cost of repairing an Indesit washing machine with error code F05 is in a wide range.

The final price is affected by:

• complexity and volume of work;
• company pricing policy;
• the need to replace individual parts or entire units.

Average prices for repair work in the capital (excluding the cost of parts):

• replacement of the drain filter – from 1,300 rubles;
• cleaning the drain filter – from 1,000 rubles;
• replacement of the drain pump – from 1,600 rubles;
• replacement of a pressure switch - from 1,6000 rubles, etc.

Companies that have been in the service provision market for a long time are fighting for their reputation - they have positive reviews from clients and always provide a guarantee for the work performed.

What to do for prevention?

In order to minimize the likelihood of error F05, Preventive measures should be followed:

1. The drain filter must be cleaned periodically to prevent it from becoming clogged.
2. It is necessary to maintain the sewerage system in working order.
3. You need to try to prevent foreign objects from getting into the tank - check the pockets of things, fasten zippers, etc.
4. Water and other liquids should not be allowed to flow into the upper part of the washing machine, as this is where the control module is located.

Recommendations

The following expert advice will help you with your work:

1. You must not tilt, much less place, the washing machine on its side until the water has been drained from it.
2. Complex repairs should be entrusted to a specialist.
3. Parts with serious damage (pressure switch, pump) require replacement.
4. When dismantling or installing parts, do not use force, as this can lead to damage to the fasteners, breakage of the part itself and other components.
5. After the repair has been completed, the washing machine should first be started in test mode, without loading it with laundry and without adding washing powder.

Read about deciphering error codes for Indesit washing machines. this section.

Conclusion

If the Indesit washing machine displays error F05, you need to find the reason for its occurrence. In some cases, the problem can be solved quite simply and quickly, but most often it is necessary to diagnose the functioning of a number of components, and sometimes to replace parts. It is not always possible to do this on your own; in this case, you will need the help of a specialist.