German quality against Russian winter: review of the Huter SGC 4000 gasoline snow blower
The German company Huter was founded in 1979. Over the years of Huter's existence, its specialists have developed and launched many models of electric generators, high-quality gardening and snow removal equipment.
The Huter sgc 4000 snow blower is a universal semi-professional equipment that can be used to clear snow from private and industrial areas.
The maneuverable model is completely autonomous and easily copes with snow removal even in narrow and cluttered areas.
Content
Description of the Huter model, characteristics
Self-propelled snow blower Huter SGC 4000 designed for clearing snow from areas whose area does not exceed 3000 m?. The device is equipped with a Huter 168F four-stroke gasoline engine (5.5 horsepower), which drives not only the cleaning unit, but also the wheels, which greatly facilitates its operation.
Reliable winter tires with wide, self-cleaning treads provide easy movement on snow and ice, and slipping is eliminated even on slippery surfaces. Thanks to the mechanical wheel locking system, the device is easy to maneuver and effectively removes snow even in a limited area.
The working mechanism of the snow intake unit is an auger - a spiral knife that, rotating, rake in the snow mass (the width of a single grip is 56 cm). Made of high-strength steel, it is reliable and not subject to wear.
The direction of movement, rotation of the chute, as well as the height of the auger relative to the ground are adjustable by the operator directly during work. The device is equipped with a fan that provides two-stage snow removal.
The snow blower runs on high-octane gasoline AI 92. You can fill the gas tank with 3 liters of fuel at a time, which is enough for 40-90 minutes of operation without refueling. The snow blower tank has a wide neck, making it easy to refuel the device if necessary.
The control unit consists of two levers and a speed switch. The wheels and snow removal auger are driven by levers. The device provides the ability to rotate the snow ejection chute by 180°. The ejection range is 13 meters.
The gear selector is connected to the manual transmission, which has 6 positions (4 for forward movement and 2 for reverse).
The operating principle of the Huter SGC 4000 snow blower is simple and clear. The collection and grinding of snow is carried out using an auger connected to a rotor. From the auger, the snow falls into a special chute for snow ejection, and the torque provides significant ejection force.
If the gutter is accidentally clogged, it is cleaned with a special tool.supplied in the kit. The direction of ejection is adjusted by turning the chute.The snow blower can operate in any, even extreme, climatic conditions and on any terrain.
Advantages and disadvantages
Most users note that the Huter sgc 4000 snow blower features true German quality at a fairly reasonable price.
When expressing your opinion about the operation of the equipment, Buyers name a large number of advantages:
The snow blower is reliable and effectively removes snow even in frosty weather.- The operation of the motor is supported by a mechanical cooling mechanism.
- Thanks to the large neck of the gasoline tank, refueling the engine is easy and comfortable.
- The device is quite compact and lightweight, which makes it portable. It can be loaded into a car and transported to the desired location, for example, to a summer cottage.
- Thanks to its small size and wheel locking system, the snow blower is maneuverable and effectively clears snow even in small areas.
- Reliable wheel treads provide good maneuverability. The possibility of slipping is eliminated even during icy conditions.
- Limit shoes protect the receiving chute from damage and help regulate the distance from the surface to the bottom edge of the auger. This feature allows you to use the snow blower on a variety of surfaces.
The equipment has much fewer disadvantages, but they still exist. Buyers note that the snow blower does not remove wet snow effectively enough.
Assembly
The snow blower is delivered from the warehouse disassembled.Proper assembly and adjustment will be the key to long-term and reliable operation of the device. They must be manufactured in accordance with the operating instructions.
The order of work is defined here:
- The control handle is installed using four bolts (included in the kit). The control handle consists of two parts. First, the lower part of the handle is attached to the body, then the upper part with the panel is attached.
- The installation of the snow ejection chute is carried out after a special protective bracket has been put on it. The gutter is attached to the body using fastening screws (included in the kit). It is recommended to lubricate the screws with machine oil before installation.
- Installation of a chute rotation lever, which allows you to adjust the direction of snow ejection. This part is attached to the body using a cotter pin, and a bracket is provided for this on the control handle.
- Installation of the gear shift lever. On the control handle there is a special board with a hole through which the speed lever passes. The lever is attached to the body tube using two bolts and nuts.
- The drive cables for the auger and wheels are mounted on the corresponding levers. So-called Z-shaped fingers are inserted into their holes (included in the package). The bushings of the auger drive cables and wheels, which ensure the functioning of these parts of the snow blower, are conveniently attached to them.
- Adjustment of limit shoes. It is important that the stop shoes are set to a position where the auger does not touch the ground. Failure to comply with these conditions will lead to breakage of the limiters and rotation of the auger. When adjusting, take into account the type of surface being cleaned. On soft and uneven surfaces, it is recommended to set the auger to its maximum height.If the surface is flat, then the auger should be located at a minimum height.
To secure the auger, special shear bolts are used. If you accidentally hit an obstacle, the shear bolt will break, thereby protecting the worm gear of the gearbox from damage.
Preparing for launch
Before use 5W30 mineral oil is poured into the engine crankcase (volume 0.6 l), and the fuel tank is filled with AI-92 gasoline (3 l).
The rotating mechanism of the chute is lubricated with lithium grease (lithol). Then the position of the limiting shoes is adjusted depending on the type of surface, and the wheel and auger drive levers are adjusted.
Before starting work, check the oil level and tire pressure (it should be about 1 bar).
How to launch and use?
After the equipment is assembled and adjusted, preparations are made to start the engine. For this open the fuel tap, after which the switch position is switched to the “on” mode. When the air damper is closed, the throttle control lever is moved to the right all the way ("Hare" mode).
The engine is started as follows: pull the starter cord until resistance is felt. Then a short and sharp jerk of the cord is made, which will lead to the engine running. Carefully release the cord, holding it with your hands. Wait for the engine to warm up, then open the throttle.
For normal operation of the snow blower, a constant oil level must be maintained in the engine crankcase.
When turning off the device, lower the wheel drive lever, and then the auger drive lever. The engine must continue to run for another 5 minutes to allow the moving parts to dry. This will make subsequent switching on easier. Then, turn the switch to the “off” position.
How to maintain and where is the best place to store?
After completing the snow removal work, the snow blower is cleaned. The auger and snow ejection chute are cleaned with a medium-hard brush. Clean the engine with a soft brush or rag. It is allowed to clean the equipment with a strong stream of water from a hose, subject to subsequent drying in a warm room.
After the equipment has operated for 25 hours, change the oil, clean the air filter and spark plug. Clean the bucket and snow supply path. All this is done with the engine turned off.
The oil change is carried out as follows:
- warm up the equipment to reduce the viscosity of the oil;
- remove the shut-off device from the tank, having previously substituted the container, and drain the oil;
- install the locking device in place;
- Fill in a fresh portion of 5W-30 oil.
At the end of the season, the equipment is preserved. To do this, gasoline is drained from the gas tank and oil from the engine crankcase, after which the mechanisms are cleaned, and the metal parts are rubbed with an oil cloth. Unscrew the spark plug and pour a little engine oil into the spark plug hole.
Rotate the crankshaft using the starter cord handle, ensuring its lubrication. After this, install the spark plug in place without putting on the cap of the high-voltage cable. The last step is to replace the gearbox lubricant.
Where can I buy?
You can buy a Huter SGC 4000 snow blower in a specialized store selling household appliances or via the Internet sitededicated to this topic. You can immediately consult with a specialist and read customer reviews.
Stores have their own delivery services, where for a fee you can order equipment delivered to your home. Payment can be made through the payment system.
Price
The cost of the Huter SGC 4000 snow blower on various trading platforms starts from 35,000 rubles.
User reviews
A powerful snow blower that handles dry and wet snow well. Goes well on slippery surfaces, comfortable control handles.
A productive snow blower with good speed and throws snow far. Consumes about 3 liters of fuel per hour of operation. Easy to start. Among the disadvantages is the difficult control of the movement and drive of the auger. Slow reverse speed. Maneuverable and stable machine, low fuel consumption. Maintenance is easy and not burdensome.
After the end of the season, when disassembling the snow blower, shortcomings were discovered (the drive ring burst on one side, the bearing in the gear shift mechanism was spinning). Needs renovation.
After clearing the snow, it was discovered that the pulley on the rotor shaft was loose. The snow blower worked for an hour. In the midst of a snowfall, the travel cable on the guide wheel broke.
Alternatives
Popular snow blower models on the market:
Husqvarna ST 224
Self-propelled snow blower Husqvarna ST 224 equipped with a 6.3 hp petrol engine. With a gas tank volume of 2.6 liters, the device is quite powerful and allows you to clean a large area without refueling. Wide wheels with reliable tread ensure good maneuverability of the snowplow even during icy conditions.
To regulate the cleaning intensity, the device has 6 forward and one reverse speeds. The device is mobile, since it is possible to change the position of the gutter by 180°. Despite the fact that the weight of the Husqvarna ST 224 snow blower is significant (90 kg), it is easy and comfortable to use.
Patriot HOME GARDEN PHG 65 E
The domestic class Patriot HOME GARDEN PHG 65 E snow blower copes well with a small amount of work. Indispensable for winter cleaning of the garden, summer cottage, small yard.
The snow blower's mobility is ensured by an adjustable snow ejection chute - it can be rotated (185°) and changed the ejection angle (within 70°). The self-propelled model is equipped with a gasoline engine, which ensures the movement of the wheels and the operation of the snow removal unit. In one pass, the device cleans a space up to 62 cm wide.
Daewoo Power Products DAST 3000E
Electric snow blower Daewoo Power Products DAST 3000E lightweight, compact, and suitable for cleaning private and small industrial areas. The device can be used for cleaning fresh, not yet compacted snow (the width and height of the bucket are 51 by 33 cm).
The model is not self-propelled, but despite this, it is quite mobile. Moving the snow blower around the site is easy, because its weight is only 16.8 kg. The snow ejection position can be adjusted thanks to a chute that rotates 190°, and this can be done either manually or using a special knob on the control panel.
The snow throw range is 10-12 m. The power of the electric motor is 4.08 hp.
Video on the topic of the article
Video review of the Huter SGC 4000 snow blower:
Conclusion
Thanks to its powerful motor and great capabilities, the Huter SGC 4000 snow blower can be used in private and industrial households, suitable for use in public utilities.
Careful adherence to startup and operating conditions, as well as proper maintenance, will ensure normal operation of the equipment throughout the entire operational period.
