Why does the Whirlpool washing machine display error F08, how can I fix it?

Whirlpool washing machines are reliable appliances that enjoy well-deserved consumer trust. But, as with any household appliance, breakdowns and malfunctions can occur with them.

In such cases, the self-diagnosis system displays an error code on the display. In some situations this may be F08.

We will tell you what error F08 means in a Whirlpool washing machine in this article.

Decoding the code

Code F08 indicates that there is a malfunction in the water heating circuit of the Whirlpool washing machine. In washing machines with a display, this problem appears as F08 or F8.

In devices without a display there is a problem with water heating is manifested by the glow of the corresponding indicator lamps:

• "Service";
• "Wash".

Why does the Whirlpool washing machine malfunction, how can I fix the situation?

F08 almost always indicates the need to repair the equipment of the Whirlpool washing machine. But in rare cases, the problem may be due to a random combination of circumstances and a failure of the control module.

This situation can be resolved by rebooting the equipment. To do this, the Whirlpool washing machine is disconnected from the power supply and turned on again after a quarter of an hour.If the problem does not go away, you need to proceed to sequential equipment diagnostics.

Problem with heating element

The heating element is a heating element that is responsible for heating water in a Whirlpool washing machine. With prolonged use, it becomes covered with plaque, which is formed from hard water, detergent residues and small debris.

Covered with a thick coating The heating element cannot provide heating of water to the required temperature and burns out.

In this case, the washing machine may display an error immediately after starting or after the water has been filled and the drum has made several uncertain revolutions.

A heating element that has become unusable cannot be repaired; it is replaced with a new part. To do this, it is necessary to partially disassemble the device.

During the diagnostic process, the heating element must be “ringed” with a multimeter and inspect visually. According to statistics, when F08 appears, a problem with the heating element is the most common situation. In addition to code F08, error F12 may indicate a problem with water heating.

How to check the heating element in a washing machine - on video:

temperature sensor

If the temperature sensor fails, the Whirlpool washing machine cannot correctly determine the degree of water heating. In this case, operation stops and F08 is issued. The solution to the problem is to replace the part.

If inspection of the heating element does not reveal any malfunctions, then you need to check the thermistor. It is located near the contacts of the water heater.

For diagnostics, the part must be removed using the following algorithm:

1. Remove the chip from the heater contacts with the wires.
2. Loosen the nut that secures the heating element.
3. Take out the thermostat.

If the thermostat is working, then it is returned to its seat, and the search for a fault in the Whirlpool washing machine continues.

Control block

The control module is a block with radio elements. When they burn out, the control unit is no longer able to control the water heating process, and the operation stops.

To carry out diagnostics, the module is removed from the housing and tested. Faulty Whirlpool elements are replaced, and tracks are soldered, if necessary. If the module is severely damaged, it may even require complete replacement.

How to perform Whirlpool diagnostics and repairs - on video:

Firmware crash

The Whirlpool control unit has firmware that contains sequences of actions for each built-in program. If the firmware is faulty, the washing machine displays various error codes, including F08.

Wiring

An open circuit in the water heating circuit in a Whirlpool washing machine or oxidation of the contacts can cause code F08 to appear on the display. The situation can be corrected by examining the wiring in the washing machine.

If a break is detected, the entire cable is twisted or replaced, and the oxidized contacts are cleaned.

Pressostat

Problem with the pressure switch - a rarer situation, leading to the appearance of code F08 on the Whirlpool display.

To analyze the condition, you need to gain access to the part. It is located in the upper part of the case, under the cover.

The pressure switch should be inspected externally and checked with a multimeter. If the resistance value does not change, the sensor has become unusable and will have to be replaced.

Calling a specialist: where to find and how much to pay a specialist?

Carrying out diagnostics and repairs of washing equipment cannot always be done on your own. If you lack skills or lack time, a specialist from a specialized company can help. Depending on the complexity of the breakdown and the company’s pricing policy, the cost for the work performed is determined.

In the capital, Whirlpool repair prices on average are as follows:

• wiring repair – from 2000 rubles;
• Firmware recovery – from 2500 rubles;
• repair of the control unit – from 2500 rubles;
• replacement of a temperature sensor – from 1600 rubles;
• replacement of heating elements - from 1800 rubles.

Prevention measures

Compliance with preventive measures helps prevent breakdowns and extend the life of Whirlpool equipment. These include:

1. For washing, use only detergents that are designed for automatic processing.
2. Do not send items for washing from which lint and pellets are separated.
3. If power surges often occur in the house, then it is better to install a stabilizer in advance.
4. Washing only at a high temperature or, conversely, only at a low temperature, contributes to a faster formation of plaque on the heating element.
5. If the quality of tap water is low, it is recommended to install a filter at the entrance to the apartment to catch foreign impurities.
6. It is necessary to clean the washing machine periodically.

4 recommendations to help

Faced with problem F08 in your washing machine, It is recommended to use the following professional advice:

1. Any repair work should only be carried out when communications are disconnected.
2. To check the functionality of the heating element, you must have a multimeter.
3. It is necessary to select a new part, including a heating element, taking into account the model of the washing machine.
4. If the washing machine is under warranty, you should not open the case yourself.

Conclusion

Error F08 in a Whirlpool washing machine indicates problems with the water heating system. To accurately determine the cause of the failure, it is necessary to conduct high-quality diagnostics.