Why does the Whirlpool washing machine display error F06 and what to do about it?
Whirlpool is a popular brand that produces reliable household appliances, including washing machines, which enjoy well-deserved consumer trust.
If a failure occurs, an error code is displayed on the device’s display, which can be used to diagnose the failure. In some cases this is F06.
We will tell you below what error F06 means on a Whirlpool washing machine, how to detect the malfunction and fix it.
Content
Decoding the code
Coding F06 almost always indicates problems with the Whirlpool tachometer. It may appear on the display in the following situations:
- The device works normally during washing, but during the spin phase it cannot reach the required speed.
- The device takes in water, begins to rotate the drum, and stops almost immediately.
- The error code appears on the display immediately after turning on the machine, the machine does not attempt to rotate the drum.
In addition to stopping operation, the Whirlpool washing machine displays an error code. This self-diagnosis allows you to narrow down the search for a problem with the equipment.
In this case, these should be the following light bulbs:
- "Service";
- "Rinsing";
- "Water stop."
If you need to clarify information on indicators or error codes, you must read the corresponding section of the instructions for a specific model.
Causes of failure and ways to resolve the problem
In very rare cases, a malfunction of a Whirlpool washing machine may be due to a coincidence. In this case, the control board freezes and operation stops.
To reboot, It may be enough to disconnect the Whirlpool washing machine from the network for a quarter of an hour, and then turn it on again.
If the problem is one-time, work will be restored. Otherwise, it will be necessary to carry out high-quality diagnostics and identify the exact cause of the failure.
You should also inspect the buttons on the control panel to make sure that none of them (especially Spin) are jammed. If it literally failed, then that could be the problem.
Tachometer
In the case when the Whirlpool washing machine does not start to rotate the drum when starting up and displays F06, then with a high degree of probability this may indicate an error in the operation of the tachometer. To accurately analyze the situation, you need to gain access to the detail. If the tachometer is burned out, it is replaced with a new one.
The tachometer is located in Whirlpool washing machines on the motor shaft. It is accessed from the rear wall.
One of the possible problems is in the video:
Motor brushes
If the motor brushes are worn out, the Whirlpool machine may not be able to gain speed during the spin phase. In advanced situations, rotation may not occur at all. If there is a problem with the brushes, sparking may even occur..
Brushes in an electric motor are consumables. During the operation of the Whirlpool washing machine, they gradually wear out, becoming smaller, and can no longer perform their declared functions.
How to replace brushes and what to pay attention to - see the video:
Control module
Failure in the Whirlpool control module may be associated both with the burnout of individual elements and with the need to resolder the tracks. For an accurate analysis, you need to remove the control module in order to carry out high-quality diagnostics by checking the triac, resistor, and relay.
If damaged elements are identified, they are replaced with new ones. In cases where the board has been severely damaged and there are extensive melted areas, it may be necessary to replace it completely.
Bearings
With prolonged use of the Whirlpool washing machine, wear of the bearing assembly is possible. Such a breakdown can also be manifested by displaying the F06 coding on the display.
If the oil seal becomes leaky or loose due to vibrations, then water may seep into the motor.. A washing machine with loose bearings does not operate stably, rattles and vibrates strongly, especially during the spin cycle.
Visually, water leakage from the seal can be seen when partially disassembling the Whirlpool washing machine. Such a failure requires replacement of the bearings. In some models with a non-separable tank design, it may even be necessary to replace the entire assembly.
Motor
If there is a problem with the motor itself, the Whirlpool washing machine may not spin the drum at all and issue F06. This situation can occur if there is a break or short circuit in the engine itself. This problem cannot be repaired - the motor must be completely replaced.
Wiring
Damage to the wiring in the circuit may cause the Whirlpool drum to not rotate. To find the location of the failure, it is necessary to partially disassemble the washing machine and check the integrity of the cables and terminals.If a defect is detected, the section is twisted or replaced.
Calling a master: what do you need to know?
It is not always possible to diagnose the operation of a Whirlpool washing machine, identify and eliminate the defect on your own. If you have doubts about your own skills, it is advisable not to experiment with expensive equipment, but to call a specialist from a specialized company.
The cost of repair depends on the complexity of the breakdown, the company’s price list and the need to replace parts, the cost of which is paid separately by the customer.
The average prices for Whirlpool in the capital are as follows:
- motor replacement – from 2500 rubles;
- replacement of wiring - from 1900 rubles;
- replacement of bearings - from 4100 rubles;
- repair of the control module – from 2500 rubles;
- replacement of engine brushes – from 1800 rubles;
- replacement of tachometer – from 1900 rubles.
After the Whirlpool repair is completed, the technician gives a guarantee for the work performed and performs a test run of the washing machine.
Prevention measures
To prevent code F06 from appearing on the display, It is recommended to adhere to simple preventive measures:
- The washing machine should not be overloaded.
- If the network voltage is unstable, it is advisable to use a voltage stabilizer.
- If uncharacteristic noise and knocking occurs during operation of the device, an analysis should be carried out to find out the cause.
- The device should not be constantly placed in a room with high humidity, as this promotes corrosion and breakdowns.
- The washing machine must be protected from children's pranks and pet mischief.
- Do not allow moisture to get on the control board and other important components.
- Do not spin shoes in the washing machine after washing.
- The device must be installed according to the rules, stable. Increased vibrations are harmful to the washing machine.
- The washing machine needs to be cleaned regularly.
Recommendations
When carrying out repair and diagnostic activities, The following expert advice can help:
- The case can only be opened when communications are disconnected.
- You should not open a washing machine under warranty yourself - you need to contact the service department.
- Before disassembling, it is advisable to drain the remaining water from the tank.
- Before you begin disassembling the case, you need to make sure you have the required tools and a multimeter for diagnostics.
Conclusion
Error F06 on the display of a Whirlpool washing machine almost always indicates the need for repair. Such work requires partial disassembly of the device for diagnostics and repairs.