Errors

LG washing machines are of high build quality. However, any household appliance can break down over time.

To facilitate diagnostics, prudent developers “taught” the device to independently recognize a malfunction and, using special sets of symbols and signs, signal this to its owner.

Read the article about how to decipher error codes in LG washing machines with and without a display.

Decoding the fault codes shown by the LG washing machine with display

If the washing machine is equipped with an electronic display, then if it breaks down or malfunctions, a code will appear on it. After deciphering it and determining the cause, in most cases the malfunction can be eliminated on your own.

O.E.

Code OE - drain does not work. Main reasons:

• the drain pump has failed;
• the pressure switch is broken;
• the drain pipe or pump is clogged;
• The control module is broken.

First, you need to check the washing machine hose for kinks or blockages.

Then they inspect the condition of the place where it connects to the sewer drain, as well as the pipe itself. If no blockage is detected, proceed to assessing the performance of the pump and other elements.

Sometimes a reboot helps solve the problem cars. If a blockage is detected, it is cleared and broken parts are replaced with new ones.

What does the OE error code mean, read Here And here.

UE

The UE (U3) code indicates an imbalance in the drum axis. Main reasons:

1. Drum overload or uneven distribution of items.
2. Incorrect installation of the device.
3. Control unit malfunction.
4. Module malfunction.
5. Bearing failure.
6. Tachometer failure.
7. Drive belt stretch.

When none of the above methods help solve the problem, you need to disassemble the case and look for failed parts. It is recommended to start the check by assessing the condition of the belt and tachometer.

What does the UE error code mean, read Here.

DE

Code DE indicates that the hatch door is not locked. However, washing does not start. Causes:

• chewed cuff;
• there is a foreign object or blockage in the lock hole;
• control module failure;
• UBL breakdown;
• broken washing machine hatch handle;
• hatch hinge failure.

First you need to inspect the lock; perhaps some foreign object is preventing the tongue from entering the hole. Then you can try to restart the washing machine. If this does not help, you will have to change the UBL, the hatch hinges or its handle. What the DE error code means, read this article.

L.E.

LE – motor blocking error. First, the machine draws water, then tries to start the drum several times, after which the corresponding code appears on the screen.

Causes and solutions:

1. Door not closing tightly. It needs to be opened and latched again.
2. The control module has failed. Rebooting the equipment will help.
3. Drum overload when operating the device in the “hand wash”, “wool” and “silk” modes. Some things need to be removed, after which you can continue washing.
4. The drum is blocked due to some small object getting inside.Inspect it, disassemble the tank, remove the mechanical obstacle.
5. Low voltage in the network. To continue washing, you will have to wait until it stabilizes.
6. The tachogenerator has broken down, the motor winding has burned out, the control module or UBL has failed. To cope with the problem, replacement of damaged elements is required.

What does the LE error code mean, read here.

A.E.

AE is the automatic shutdown code. Causes and solutions:

• there was a failure in the operation of the control module - a reboot of the equipment is required;
• water has accumulated in the pan (for machines equipped with Aquastop technology) - if this is the case, you need to check all the clamps and hoses, perhaps one of them has simply come loose;
• The control module is broken and needs to be replaced;
• the hatch cuff, pipes or tank are leaking and need to be replaced;
• The Aquastop system has failed - it is being repaired or replaced.

C.E.

The CE code appears when the washing machine motor is overloaded. Causes and solutions:

1. There is too much laundry in the drum. It needs to be unloaded.
2. There was a malfunction in the control board. Rebooting the equipment will help.
3. Damage to the motor, bearings, tachometer or control module. All listed parts are subject to repair or replacement.

F.E.

When the FE code appears, the washing machine stops washing and constantly fills and drains water. Causes and solutions:

• there is too much foam in the drum - you need to drain the water, take out the laundry and let the machine stand with the door open for 24 hours;
• failure of the control module - the machine must be rebooted;
• the intake valve, pressure switch, control unit has failed, or the wiring has frayed - the detected malfunction is corrected by replacing or repairing parts.

I.E.

The IE code appears when starting the wash, but the machine does not draw water. Causes and solutions:

1. There is no water in the tap or the pressure is too low. You need to pause the washing and wait for the situation to stabilize.
2. The shut-off valve is closed. It needs to be opened.
3. The inlet hose is squashed. The mechanical obstacle is removed.
4. The filter where the inlet hose is attached to the washing machine is clogged. It needs to be cleaned.
5. The control module has failed. A reboot will help.
6. The intake valve, pressure switch or control board is broken. Faulty parts are repaired or replaced.

Details - in this article.

P.E.

The PE code appears when a person tries to start a washing program. In this case, the device does not perform any further actions. Causes and solutions:

• failure of the pressure switch - it needs to be replaced, this is the most common cause of the PE error;
• control board failure - the machine needs to be rebooted;
• the wires going to the pressure switch have come loose - they need to be fixed;
• The control board is broken or the wiring is damaged - repair or replacement is required.

PF

The PF code appears during the washing process, and the machine simply stops working. Causes and solutions:

1. Problems with the power supply: it is turned off or there are surges in the network.
2. The power cord is damaged. It needs repair or replacement.
3. The electronic controller has failed. Rebooting the device will help.
4. The wires leading from the interference filter to the control module have come loose.
5. The control module or heating element is broken. Damaged parts need to be replaced.

Details - in this article.

tE

The tE code appears during the washing phase when the machine draws water but suddenly stops. In this case, the hatch may be cold even if the hot water washing mode is selected.

Causes and solutions:

• The heating element is broken and needs to be replaced;
• there was a failure in the operation of the control module - the machine is rebooted;
• the wiring between the heating element and the module has come loose, it needs to be fixed;
• The temperature sensor or drying sensor has failed - they are replaced.

S.E.

Code SE (5E) appears after the machine has filled with water, but the wash does not start and the drum does not rotate. Causes and solutions:

1. The Hall sensor (tacho sensor) is faulty. This breakdown is diagnosed in 90% of cases. The part is being changed.
2. The motor or control module is broken. Needs repair or replacement.
3. Control module malfunction. The machine is rebooted.
4. The wires leading to the motor came loose.

C.L.

The CL code appears when the child lock function is turned on. This is not an error, but an informational message.

If the device has an electronic display, Pressing the following keys simultaneously will help:

• pre-wash and super rinse;
• add. rinsing and intensive washing;
• temperature and the Options button (one of them).

Read more here.

tCL

The tCL code is not an error code, it is an informational message that indicates that it is time to run the drum cleaning function. It appears every 30 wash cycles.

To remove the inscription, you need to start the cleaning process. It happens automatically.

If a person does not consider it necessary to clean the drum, they should turn off the device by pressing the power button.The device will regard these actions as a failure and the code will not appear the next time it is turned on. Will tell you in more detail this article.

E1 (01)

Code E1 (01) appears if water has accumulated in the tray of the washing machine. Sometimes it may not be there, but the error is still displayed on the screen.

Causes and solutions:

1. The tank or hoses have become depressurized. It is necessary to check their integrity.
2. The water leakage sensor is broken. It needs to be replaced.

Sometimes rebooting the device helps resolve the error.

E3

Code E3 is very rare; it indicates a load detection error or a control module failure. To fix the problem, you need to estimate the amount of laundry in the drum. If there is not much of it, restart the machine. When none of these methods helped eliminate the E3 code, you will have to call a technician.

HER

The EE code appears on the device screen infrequently and indicates a loading error. Sometimes it is displayed once, after the first start of the device. To eliminate it, it is recommended to reboot the equipment. If immediately after switching on the code is displayed again on the display, you should check the serviceability of the electronic controller.

HE

In some models of LG washing machines, a faulty heating element is indicated by the HE code. Wherein The device will not heat the water, but the wash will not stop.

Cd

If the LG washing machine displays a cd code on the screen, you should not worry. It is not a mistake. This letter code refers to information messages and it appears only on devices equipped with drying.

The inscription cd indicates that the cooling mode is running.To reset the code, just press the “Start/Pause” button. This will terminate the program.

What do the signals from an LG washing machine without a display mean?

If the washing machine is not equipped with a display, then errors appear on it in the form of a set of signals. The most common of them are described in the table:

What do error codes mean for LG washing machines without a display, read Here.

Call the master

It is not always possible to handle washing machine repairs on your own. If difficulties arise, you should seek help from a specialist. Finding a master is not difficult. There are advertisements on the Internet and in newspapers.

List of estimated costs of work:

1. Pump replacement – ​​from 2100 rubles.
2. Replacement of the pressure switch - from 2100 rubles.
3. Clearing a blockage in a drain pipe, pump or hose – from 1,400 rubles.
4. Replacement of a temperature sensor – from 1,700 rubles.
5. Repair of the control unit – from 2600 rubles.
6. Replacement of bearings and oil seal - from 4,300 rubles.
7. Replacement of tachometer – from 2600 rubles.
8. Belt replacement – ​​from 1200 rubles.
9. Repair of UBL – from 1700 rubles.
10. Replacing the hatch handle – from 1,700 rubles.
11. Adjustment of hatch hinges – from 1600 rubles.
12. Repair of the Aquastop system - from 2600 rubles.
13. Tank replacement – ​​from 4600 rubles.
14. Replacement of pipes - from 1400 rubles.
15. Cuff replacement – ​​from 2100 rubles
16. Replacement of wiring – from 2000 rubles.
17. Replacement of the inlet valve - from 2000 rubles.

Read about self-repair of an LG washing machine in this section.

Conclusion

Error codes on LG washing machines inform the user about malfunctions and help quickly understand what exactly the problem is. This makes working with household appliances much easier.