Step-by-step instructions on how to remove the top cover of an Indesit washing machine

To access the internal structure of the Indesit washing machine, it is often necessary to remove the top cover.

With equipment from this manufacturer, it is not always easy to gain access to the device from above.

We will tell you in the article how to remove the top cover of an Indesit washing machine with vertical and front loading.

Preparing for removal

Removing the top panel for washing machines from different manufacturers can vary significantly.

Before starting work, It is necessary to carry out the following preparatory actions:

1. You need to make sure there is no laundry in the washing machine and the water is drained. If this is not done, you need to drain the water and remove the laundry.
2. You should disconnect the washing machine from the power supply. To do this, you need to remove the plug from the socket.
3. The water supply to Indesit must be shut off.
4. It is necessary to provide access to the washing machine from all sides. To do this, the car is pulled out and space is cleared on all sides.

It is advisable to take care of the tools that may be useful in your work in advance.

Sequence of actions and features

Removing the lid from front-loading models differs from those with vertical loading. In each option the procedure will be different.

How to open a top-loading washing machine?

If it is necessary to remove the top cover from a top-loading Indesit washing machine, you will also need to remove the dashboard.

The disassembly process has its own characteristics:

• pull out the washing machine so that it is accessible from all sides;
• Unscrew the fixing screws from the rear wall - they are located behind the dashboard;
• the control unit is retracted up and forward - this must be done carefully, since the supply wires pass under the plastic;
• after disconnecting the control panel, access to the retaining screws opens; they need to be unscrewed;
• remove the cover.

The process of removing the lid from a top-loading washing machine can be seen in the video:

From the front

When removing the lid from a horizontal-loading model, be aware of the tight plastic latches. It is very important not to damage them, since it will be impossible to fix the damage.

Work algorithm:

1. The washing machine must be pulled out so that it is possible to enter from the rear.
2. On the rear panel side, there are two screws at the top. They need to be found and unscrewed.
3. It must be located on the back wall of the washing machine.
4. Lift the back side of the cover with your hands and pull it towards you until it clicks. This is the latching signal.
5. If the previous method did not work to move the panel, you need to walk around the washing machine and stand on the front side facing the machine.
6. You need to rest your hands on the top of the plastic and push it away from you.

The detailed process of removing the cover is shown in the video:

How to return the part to its place?

After repair work has been carried out on the removed top plastic panel, it must be returned to its original position. To do this, all steps are performed in reverse order..

For machines with horizontal loading, the lid is placed on top of the machine and moved towards the front side so that the latches are activated. This will ensure reliable fixation of the part in a certain position. But you also need to tighten the previously removed screws.

In a top-loading machine, the procedure is performed in the opposite direction to disassembly. Just as in the case of a horizontal loading machine, it is necessary to fix the part with the previously removed screws. After this, the control panel is installed in place. And it also needs to be secured with screws.

If the mounting screws are heavily rusted, they can be replaced with new ones of the same size at the stage of securing the cover.

Possible mistakes

While removing the cover from the machine there may be the following errors:

1. The tight movement of the lid in a front-loading washing machine should not be accelerated by prying the part with a knife, screwdriver or other tool.

   This can cause the latches to break and damage the plastic in other places.

2. Excessive force may damage the plastic fasteners.
3. When removing the cover, the removed screws should be placed in a certain place, otherwise they may get lost.
4. If, in addition to removing the top panel, you need to dismantle other components, you must prepare not only screwdrivers, but also other tools - pliers, wrenches, etc.
5. If the screws securing the cover to the device are very rusty and you cannot unscrew them, you should not simply use force. Try to soak the mono thread using gasoline, kerosene or WD-40.

A lot of important and useful information about the repair of Indesit washing machines is presented in this section.

Conclusion

It is possible to remove the top cover from the Indesit washing machine on your own. All you need for this is a screwdriver or an electric screwdriver. Work should be carried out in a certain order, without applying excessive pressure, as this can lead to damage to the plastic fasteners (latches).