How to replace the pump of an Electrolux washing machine yourself?

The pump is one of the most important components of a washing machine. Any malfunction has a negative impact on the quality of washing - the liquid remains in the tank, and the laundry turns out to be excessively wet.

To fix the problem, you will need to timely replace the pump of your Electrolux washing machine. You can cope with this task yourself.

What is a pump and what functions does it perform?

Water pump or washing machine pump - one of the main technical units that ensures uninterrupted operation of the entire device. This is an asynchronous motor consisting of a housing (volute), a filter and a suction device.

The drain pump ensures the flow of water into the drum of the washing machine, and after washing it drains and pumps out the waste liquid.

Principle of operation

The Electrolux washing machine pump is involved in almost all washing modes. It is activated automatically, immediately after selecting the desired program and pressing the “Start” button.

Supplying water to the washing machine drum occurs in several stages:

1. The solenoid valve opens.
2. The liquid level sensor determines the volume of water required for washing.
3. Water passes through compartments filled with detergent and mixes with it.
4. The dissolved washing powder or gel-like product enters the tank.
5. The required volume of liquid under pressure enters the chamber with the laundry.

After the washing process is completed, the water pump works in this mode:

1. The electronic module sends a signal to the pump and the waste liquid begins to be pumped out through the impeller.
2. The liquid comes out through a drain hose connected to the housing.
3. The dirty water remaining after washing is pumped out until the tank remains empty.

Where is?

Like other control units of the washing machine, the pump located at the bottom of the device, under the tank. This location makes it easy to reach when you need to drain excess water or perform a thorough cleaning.

Access is quickly gained by removing the back cover of the device, which is secured with several bolts.

Typical faults

About the failure of the Electrolux washing machine pump, Several signs may indicate:

• malfunctions or sudden stoppage of the device during washing.
• incomplete water supply;
• buzzing when pouring water and draining waste fluid;
• lack of response to programs.

To determine whether the pump requires replacement or repair is sufficient, diagnostics should be carried out:

1. Listen to the pump while the washing machine is running to see if there are any extraneous sounds.
2. Inspect the drain hose for blockages.
3. Open the housing and clean the filter from accumulated dirt.
4. Check the operation of the drain pump impeller to see if it rotates normally or if jamming occurs.

The most common faults, characteristic of the drain pump of an Electrolux washing machine, include:

• filter clogged;
• hose clogged or damaged;
• jamming of the impeller (pulley).

The cause of all these problems is the ingress of threads, hair, foreign objects and debris. To fix problems, you need to:

1. Carefully remove the filter and drain hose.
2. Clean the filter from dirt.
3. Rinse the hose under running hot water.
4. Check the operation of the machine by running the test wash mode.
5. In the rinse mode, check whether the water is pumping and draining normally.

The impeller is located directly under the filter, so To check its functionality you need to:

1. Unscrew and remove the filter.
2. Inspect the appearance of the hole, using a flashlight if necessary.
3. Manually rotate the impeller blades, checking how smoothly it moves.
4. If it jams, remove any stuck debris and foreign objects.
5. Reinstall the filter and perform a test wash again.

If after performing all the above steps the washing machine works normally, you should not do anything else. But if the failures continue, it means that more serious damage to the mechanism has occurred. They can only be eliminated by replacing the pump.

How to replace a part of an Electrolux washing machine?

Difficult movement of the pulley without blockages and the presence of foreign small objects is a serious reason to replace the pump. You can do this yourself by understanding the sequence and rules of the work.

How to remove it correctly?

In order to remove a failed Electrolux washing machine pump, you need to do the following:

1. Disconnect the device from the power supply and water supply.
2. Unscrew the screws on the back of the top panel and carefully remove the panel.
3. Press the latch located on the back and remove the dispenser tray.
4. Unscrew the bolts of the washing machine body and the screws in the upper part above the panel with control units.
5. Push back the latches and carefully remove the panel.
6. Using pliers, pull out and remove the spring clamp.
7. Remove the rubber door seal.
8. Raise the washing machine slightly and place a wooden block under it for better stability.
9. Unscrew the bolts located in the base of the front panel of the device.
10. Remove the wooden block and place the machine in its natural position.
11. At the top of the panel, unscrew the bolts and remove the panel by lifting it and pulling it towards you.
12. Disconnect the wiring harness connector from the panel.
13. Remove the clamp located under the tank and carefully disconnect the drain pipe. In case of a possible leak, prepare a rag and a small container to collect water.
14. Move the clamp and disconnect the drain hose connector.
15. Unscrew the mounting screws and remove the damaged pump.

How to change to a new one?

After removing the old pump you will need:

1. Install the new pump in a previously cleaned seat, press tightly and screw it on.
2. Connect the connector.
3. Place the drain hose in the appropriate place and secure with a clamp.
4. Install the pipe and also secure it with a clamp.
5. Reassemble the parts in reverse order.

The video will show you how to remove and replace the pump of an Electrolux washing machine:

Rules for operating a household appliance and preventing damage

If you follow preventive measures and operating rules, the Electrolux washing machine pump will reliably serve for at least ten years without needing replacement.

To increase its service life it is necessary:

• monitor the cleanliness of the water; before washing, be sure to remove pieces of dried dirt from clothes and other things;
• remove various items from clothing pockets in a timely manner;
• regularly check the cleanliness and functionality of the filters;
• prevent scale formation by adding special additives to the water;
• After each wash and rinse, wait until the working tank is completely empty of waste liquid.

Price and place of purchase of the pump

You can buy a pump for an Electrolux washing machine in household appliance stores and supermarkets, as well as in online stores. This device is always available in the manufacturer's official store.

The cost of the pump varies from 1900 to 3500 rubles, depending on the model of the device and the retail outlet where the purchase is made.

Cost of the master's services

Pump replacement services are provided by specialized service centers. The cost of work starts from 1,700 rubles.

Conclusion

Replacing the pump of an Electrolux washing machine may be necessary if the natural process of drawing and draining water is disrupted or the operation of the appliance suddenly stops.

By following the instructions and recommendations provided, you can handle this task yourself. But if you don’t have confidence in your own abilities, it’s better to call an experienced specialist.