What are the reasons for the flow from the bottom of the Bosch washing machine?
Despite all the reliability of Bosch washing equipment, it can also break down. One of the critical problems is the appearance of a leak from the bottom of the machine.
Such a problem cannot be ignored and will require an urgent solution.
What are the reasons that a Bosch washing machine is leaking from below, what to do in this situation?
Content
- What to do?
- Why did the leak occur?
- How to detect a breakdown and fix it?
- Inaccurate placement of items in the drum
- Poor fastening of the inlet hose
- Damage to the inlet hose
- Drain filter clogged or incorrectly installed
- The hatch cuff is torn
- The powder receptacle is clogged
- The drain pump is broken
- Tank damage
- Pipes
- The water level sensor is broken
- Fill valve failure
- Bearing wear
- Drain hose problem
- Do-it-yourself repair or call a specialist: what to choose?
- Conclusion
What to do?
If a puddle begins to form under your Bosch washer, you need to act quickly. Otherwise, a short circuit or a flood may occur.
Procedure:
Unplug the washing machine. If it is impossible to unplug the plug from the socket without stepping into water, you must turn off the electricity to the apartment.- Turn off the water supply to the washing machine.
- Collect spilled water from the floor.
- Drain the remaining water in the device through the drain filter.
- Remove the laundry from the drum.
Only after completing all of the above steps can you proceed to finding the cause of the leak. You can carry out the analysis either on your own or by calling a specialist from a washing machine repair company.
Why did the leak occur?
It is possible to determine what is broken in a Bosch washing machine by the nature of the leak. For this It is advisable to pay attention at what stage the failure occurred:
| Washing stage | Which node should be analyzed |
| Water set | inlet hose, powder receiver, inlet valve, inlet pipes, water level sensor |
| Wash | tank, cuff |
| After washing | tank, drain system |
| Spin | bearings, tank |
| Draining | drain filter, drain pump, drain pipes, drain hose |
How to detect a breakdown and fix it?
In some cases, a leak from under a Bosch washer is explained by a user error and is not a breakdown. The analysis should begin with simple nodes, gradually moving towards diagnosing those that are difficult to access.
Inaccurate placement of items in the drum
If the laundry was placed in the drum carelessly, the hatch door may accidentally press one of the items. As a result, there will be no necessary tightness, and water will begin to leak from the drum in the place where the laundry is clamped by the door.
Such a user error is not a breakdown of the Bosch machine, but can lead to deformation of the rubber cuff and malfunction of the hatch door lock.
Poor fastening of the inlet hose
The inlet hose is connected to the Bosch washing machine from the rear wall using a plastic nut.
If the connection is not securely fastened, water may leak. along the back wall of the washing machine, and spread across the floor.
The solution to the problem is to check the fasteners and tighten the nut if necessary. If the nut is broken, the hose must be replaced.
Damage to the inlet hose
The water inlet hose for a Bosch washing machine is highly durable and can last for years without losing its functionality.But there are situations when the hose is damaged, crushed, for example, by furniture. If the hose is defective, it is replaced.
Drain filter clogged or incorrectly installed
The drain filter is located at the bottom of the Bosch washing machine. This part is designed to catch and hold debris., who accidentally got into the drum with things.
The filter must be cleaned periodically. If the unit has not been cleaned for a long time, it may leak. Water can also spill out when the filter was installed incorrectly - with a skewed thread, not screwed tightly, or when a foreign object got under the thread.
How to clean - on video:
The hatch cuff is torn
The rubber cuff, which is located around the perimeter of the hatch, can cause a leak if it is damaged. The part may be damaged due to:
- pet pranks,
- children's mischief,
- frequent jamming of foreign objects by the door.
Long-term use and drying out can also lead to wear.
The powder receptacle is clogged
If the powder receptacle cuvette is clogged, the water entering during collection does not have time to drain into the drum, and may leak onto the floor. Moreover, in some cases, the leak occurs from the inside of the housing, and it can only be noticed by the puddle that has spilled on the floor.
The solution to the problem is to clean the powder cuvette. For ease of operation, the powder receptacle is removed from the seat and cleaned.This problem can be caused by either the adhesion of powder or the ingress of foreign objects. For example, children's toys.
For washing, you should only use powders that are intended for automatic washing machines.
You can learn how to eliminate a leak in this unit from the video:
The drain pump is broken
The Bosch drain pump is located at the bottom of the washing machine. If it burns or is otherwise damaged, a leak may form. To access the unit, it is necessary to partially disassemble the washing machine body. If the pump is broken, it will need to be replaced.
Tank damage
The Bosch washing machine tank is a durable part that can withstand heavy loads. But trouble can happen to her too.
A crack in the tank can appear for various reasons:
- entry of a foreign object into the tank (key, coin, nail, etc.), which damages the integrity of the housing;
- frequent washing and spinning of shoes and other user errors;
- as a consequence of poorly tested previously repairs.
If the damage to the Bosch tank is due to a foreign object, you may initially hear squeaking or scratching sounds during the wash and spin cycle. Uncharacteristic noise indicates that a foreign object is interfering with the free movement of the drum. By responding quickly to the problem, damage to the tank and costly repairs can be avoided.
Replacing a Bosch tank is a complex procedure that requires complete disassembly of the washing machine. It is better to entrust such repairs to professionals in a workshop..
Pipes
To analyze the condition of the pipes, the Bosch washing machine needs to be disassembled. These parts can either become unusable due to wear or fall off if the clamps are poorly secured.
If integrity is lost, the pipes are replaced. If the problem was in the clamps, then the connection is restored.
The water level sensor is broken
If the water level sensor in the tank is faulty, overflow is possible. With such a malfunction, incorrect information is supplied to the control module, and the Bosch washing machine cannot determine how much water is in the tank.
Fill valve failure
The fill valve is located on the top of the Bosch washing machine, above the tank. Its failure can lead to water overflow. The part is dismantled for analysis. If repair is not possible, the valve must be replaced.
Bearing wear
When the bearings wear out, not only water leakage is possible, but also loud noise., especially during the spin cycle. In addition, grease and rust may stain items in the wash.
Drain hose problem
The drain hose, like the inlet hose, can be damaged if handled carelessly. If it turns out to be so severely deformed that it leaks, it is replaced with a new one. But in the case when the problem is a leak in the section where it taps into the sewer, the situation can be corrected by connecting the hose according to all the rules.
Do-it-yourself repair or call a specialist: what to choose?
Simple malfunctions with a Bosch washing machine that lead to leaks can be fixed on your own, without involving a technician.
Such situations include:
- Cleaning the drain filter.
- Checking the correct connection of communication connections.
- Cleaning the powder receptacle.
- Eliminating causes that are the result of user errors.
But complex repairs require special knowledge and tools. In such cases, it would be better to take the help of a specialist.To eliminate a leak in the device, you need to contact a company that repairs washing machines.
If a company has been operating on the market for a long time, has a lot of positive feedback from clients and values its reputation, it can be trusted. The cost of the work will depend on the complexity of the breakdown and the company’s pricing policy.
In the capital, the average repair prices are:
- replacement of detergent dispenser – from 1,000 rubles;
- cuff replacement – from 2,000 rubles;
- replacement of the inlet hose – from 1,100 rubles;
- replacement of the drain filter – from 1,600 rubles;
- replacement of the drain hose – from 1,500 rubles;
- cleaning the drain filter - about 1,300 rubles;
- replacement of a water level sensor – from 2,000 rubles;
- replacing the fill valve - about 2,000 rubles.
Conclusion
If your Bosch washing machine is leaking from below, this situation requires solving the problem. In some cases, fixing a leak is not at all difficult on your own. But if the problem is more serious and complex repairs are required, it is recommended to use the services of a washing machine repairman.
