Recommendations for replacing shock absorbers in a Bosch washing machine yourself

Shock absorbers in a Bosch washing machine serve to dampen excessive vibrations of the tub during the washing process and help stabilize its position.

With prolonged use, parts wear out, resulting in their functionality decreasing.

Dampers that have become unusable must be promptly replaced, since ignoring the wear of shock absorbers can lead to even more serious damage and costly repairs.

We will talk about replacing shock absorbers in a Bosch washing machine below.

How to determine that it is necessary to replace parts of a Bosch washing machine?

Wear of dampers in a Bosch washing machine becomes noticeable by a number of signs:

• high vibration, especially during spinning;
• knocking noise when washing and rinsing;
• knocking noise when the drum stops.

Strong vibrations can lead to other disruptions in the operation of other components. This could be, for example, leaks and physical damage to components that suffer from tank vibrations.

Reasons that lead to damper wear:

• wear;
• long-term loads;
• improper installation, which leads to strong vibration;
• violation of operating rules;
• lubricant drying out;
• constant overload of the drum.

The movement of the drum with weak shock absorbers over a large amplitude breaks the tightness of the connection between the drum and the hatch, and can lead to water leakage during washing.

Preparation

Before you start replacing Bosch shock absorbers, you need to prepare. At this stage, perform the following actions:

1. The washing machine is disconnected from the electricity and the water supply tap to the device is closed.
2. The laundry is taken out of the drum.
3. The washing machine is pulled out to allow access to the device from all sides.

It is also necessary to ensure that you have tools and new dampers for replacement. The required set of tools includes:

• screwdriver;
• set of heads;
• drill 13 mm;
• screwdrivers;
• awl;
• pliers.

You will also need 2 13mm bolts and nuts to secure them.

How to remove and change?

Bosch shock absorbers are conveniently accessible from the front wall of the washing machine. To do this, it is necessary to partially disassemble the housing.

Procedure to ensure access to shock absorbers:

1. Unscrew the screws that hold the top cover of the washer.
2. Remove the top cover.
3. Pull out the powder receptacle.
4. Unscrew the screws that hold the control panel.
5. Carefully remove the control panel and place it on top of the machine.
6. Open the hatch door.
7. Under the elastic band, find the wire clamp that holds it in place.
8. Pull out the clamp.
9. Place the rubber band inside the drum.
10. Remove the screws that hold the front panel.
11. Detach the front panel carefully, as it will continue to be held by the UBL.
12. Disconnect UBL.
13. Move the front panel to the side.

Shock absorbers are located under the tank on both sides. Later a Bosch washing machine can be repaired in two ways:

• by complete disassembly, including removal of the tank;
• without removing the tank.

The last option is simpler and faster. To make sure that the noise during washing was actually created by shock absorbers, you need to pump the tank by hand. If a part begins to actively move from a slight touch and does not stabilize its position for a long time, most likely the shock absorbers are not performing their function.

Even if only one of the dampers is worn out, replace them in pairs. Each shock absorber has two attachment points: to the tank and to the washing machine body. The upper fastenings are made with plastic rivets. To remove them, you will need a screwdriver and a 13mm drill bit.

Assembling the washing machine is carried out in the reverse order, not forgetting to connect the door lock and install the clamp on the hatch rubber.

One of the options for replacing shock absorbers on a Bosch washing machine can be seen in the video:

Rules for selection and price of new dampers

The selection of shock absorbers from Bosch for replacement should be carried out not only taking into account the manufacturer, but also taking into account the model of a particular washing machine. Dampers can be sold in pairs or individually. The cost of the set is from 600 rubles.

You need to choose high-quality shock absorbers that match the washer model in size and hardness. You should not take stiffer shock absorbers, since this parameter is calculated by the manufacturer, and installing inappropriate parts may cause equipment breakdowns.

How to choose shock absorbers and what to pay attention to - in the video:

Call the master

In the event that it is not possible to replace Bosch shock absorbers with new ones on your own, you can call a specialist. It is best to contact companies that have been operating in the market for a long time and provide high-quality repair services for washing equipment. This can be judged by positive customer reviews. This will allow you to trust your equipment to the pros and not fall for scammers.

After the new shock absorbers are installed, the technician performs a test run of the work and provides a guarantee for the repairs performed.

Conclusion

Replacing shock absorbers in a Bosch washing machine is a moderately complex repair that can be carried out even on your own if you have the appropriate knowledge and a set of tools. Otherwise, repair is possible with the participation of a technician from a washing machine repair company.