Instructions on how to remove and replace the heating element in the Atlant washing machine
Atlant washing machines have proven themselves to be reliable appliances. Breakdowns are rare, but sometimes they do happen.
If during operation problems arise with heating water, then with a 95% probability the cause comes down to a malfunction of the heating element.
Read the article about what this part is, where it is located and how to replace the heating element in the Atlant washing machine.
Content
What is it and why is it needed?
The abbreviation TEN stands for “tubular electric heater”. It is represented by a tube in the shape of the letter W or V, inside of which there is a spiral. Its free space is filled with crystalline magnesium oxide. This insulator is designed for better heat conduction.
The outside of the heating element is covered with a protective layer. Its ends are connected to contacts through which electricity flows into the tube. Next to it is a temperature sensor that measures the degree of heating.
When switched on, the heating element heats the water to the desired temperature. It receives commands from the electronic module to which it is connected by wires. When the liquid inside the drum reaches the desired temperature, the temperature sensor sends a signal to the control board, and it sends a signal to the heating element. It turns off, after which washing continues with the specified parameters.
Signs of a malfunctioning heating element
The fact that the heating element is faulty or does not work properly, indicate the following signs:
The water does not heat up, remaining cold throughout the entire cycle. This is not difficult to understand; just touch the glass of the sunroof with your hand.- Heating is carried out, but it is weak. For example, at a selected temperature of 90 degrees, it does not exceed 60 degrees.
- A cracking noise is heard during operation of the device. In this case, the craftsmen say that the heating element “breaks through”.
- When you turn on the device, a burning smell appears.
- Code F is displayed on the display. This is a water heating error, which may indicate a malfunction of the heating element or temperature sensor.
- If you touch the body of the machine, you may receive an electric shock.
One or more of the listed signs is a reason to check the heating element for performance.
An indirect signal of a malfunction of the heating element is a short circuit with knockout of the meter machine. A similar breakdown occurs every time the washing machine is turned on.
Where is the part?
To find the heating element, you need to remove the back cover of the Atlant washing machine. The electric heater is located at the bottom of the device, on the left side of the tank. There is a slot for it in which it is inserted.
In some SMA Atlant models, the heating element is installed at the bottom of the tank. Next to it you can see colored wires that lead to the control board. There is also a temperature sensor located in close proximity.
How to remove it from the washing machine?
To remove the heating element, You will need the following set of tools:
- crosshead screwdriver;
- flat screwdriver;
- wrench 8;
- lubricant - it will come in handy if the bolts are very rusty, the best option is VD-40;
- multimeter
To remove the heating element, operate as follows:
Disconnect the device from the network.- Drain the remaining water in the drum. You can use an emergency hose to do this.
- Turn off the water supply tap.
- Disconnect the inlet hose. The drain hose is removed from the sewer drain.
- Unscrew the bolts holding the back wall, remove it and set it aside.
- They find a heating element. If inspecting the part is problematic because of the belt, it must be removed.
- Assess the tightness of the contacts to the terminals of the heating element. If one of them has come off, it must be returned to its place, and then the functionality of the equipment must be checked. If there is no heating, the process of removing the part continues.
- Unscrew the main nut, which is located in the center. Remove the temperature sensor.
- Press the bolt inward to depressurize the seal.
- Using light rocking, remove the heating element from the socket.
When removing the heating element from its seat, you must act carefully so as not to damage it. If force is applied to the burnt area, the tube may break off. Getting the rest of it will be problematic.
How to replace?
After the heater is removed from the groove, it must be inspected for the presence of scale. If there is a lot of it, but no signs of burning are visible, the part is cleaned of plaque..
To do this, prepare a solution based on acetic acid, in which the tube is soaked, after which its performance is checked.
The algorithm of actions is as follows:
- Buy a new heating element.
- Inspect the groove in which the heater was installed. Most often, dust and dirt accumulate in it during operation. You can remove it with a brush.
- Lubricant is applied to the rubber seal and the groove.
- Install the working part.
- Fix the temperature sensor.
- Tighten the fasteners and connect the wires.
- Install the back panel and screw all the bolts back in.
After connecting the machine to the communications, you need to check the functionality of the heater. To do this, start the wash cycle, but without laundry. The water temperature should be at least 60 degrees. If heating is carried out as expected, then the repair was successful.
Video instructions on how to replace the heating element in an Atlant washing machine:
Features for top-loading appliances
There is no fundamental difference between the process of removing the heater from a machine with vertical and horizontal loading. However, there are still certain differences.
Therefore, before starting work, you need to read the instructions, which includes the following steps:
- the device is disconnected from electricity and other utility resources;
- remove the side panel by twisting the bolts;
- They find a heating element under the tank and disconnect the wires from it;
- loosen the central nut, press in the bolt;
- take out the heater;
- clean the seat and install a new part;
- return the panel to its place, fix it with bolts.
Where and at what price can I buy a new one?
Heating elements can be purchased in stores specializing in the sale of spare parts for household appliances. You can also order the original part in online markets.
In order for the heater to fit the Atlant washing machine, you need to know exactly its model. If the purchase is made at retail, you can show the seller the old removed part.
You should not buy a heater that has already been used before. Such an offer may come from private craftsmen who repair washing machines. They remove working parts from faulty devices and then resell them to other customers. You should not agree to such a deal, since there is no guarantee that the old heating element will work properly.
The cost of a new heating element for the Atlant washing machine is 900 rubles. This is the average price, which may vary depending on the model of the device and the markup of the retail outlet.
Call the master
If you can’t cope with replacing the heater yourself, you need to call a specialist. The cost of work is about 1800 rubles. You can contact either a private person or a service center.
In order to minimize the risk of encountering scammers when choosing a specialist, you need to study the reviews of other clients left on forums and websites. You can also use word of mouth and contact a specialist who has previously repaired equipment for relatives or friends.
Before agreeing to carry out work, you need to clarify its cost. After completing the repair, the repairman must provide receipts for the replaced parts, as well as provide a guarantee, the minimum period of which is six months.
Conclusion
The heating element is responsible for heating the water in the Atlant washing machine. If it breaks, you will not be able to fully use the device. You can replace the part yourself, or seek help from a specialist.
