Simple ways to remove sticker adhesive from metal

Traces of glue from stickers are found in the most unexpected places: on the refrigerator door, on the sink, on the surface of the iron and more.

Dealing with the problem is not as easy as it might seem at first glance, because the sticky layer is very strong. Therefore, it will not be possible to get by with just plain water.

How remove glue from metal stickers, read the article.

How to remove label marks from a metal surface?

The sooner you start removing the adhesive after removing the sticker, the easier it is to deal with. Sometimes it is enough to simply wipe the stain with a cloth soaked in a soapy solution. If time is lost, you will have to use more aggressive compounds.

Soap

Fresh stains can be easily removed with a soap solution. Method of its preparation:

1. Rub 72% laundry soap into the shavings.
2. Add warm water to the container.
3. Stir the composition.

It is better to use the solution before it cools down. It is applied to the stain with a sponge, generously wetting the trace of glue. After 15-30 minutes, rub the metal with a soft brush and wipe with a cloth to remove any remaining product.

If the stain is not removed the first time, repeat the procedure.. The soap solution does not harm the metal surface, so you can use it as needed.

The main disadvantage of this method is its low efficiency in the fight against old marks.

Petrol

Gasoline dissolves glue molecules well, making the bonds between them less strong. Thanks to this effect, it can be easily removed.

To treat metal surfaces, gasoline is used to refill lighters. Mode of application:

• soak a cotton pad with gasoline;
• apply it to the glue stain;
• leave to act for 20 minutes;
• roll the softened glue with a plastic spatula or scraper;
• Wipe the surface with alcohol to degrease it and remove unpleasant odors.

Dimexide

Dimexide is a drug for the treatment of inflammation and the destruction of microbes, it is sold in pharmacies. In undiluted form (99% concentration), the composition is very aggressive, so it copes even with old stains. Its cost is low - about 80 rubles per 100 ml.

Mode of application:

1. Apply Dimexide to a cotton pad.
2. Moisten the stain with it.
3. Leave to act for 5-10 minutes.
4. Remove glue and remaining product with a paper towel.
5. Wipe the surface with a clean damp cloth.

Dimexide does not harm the metal, but with prolonged contact it can cause destruction of its protective coating. Therefore, you should not keep it on the surface for more than 10 minutes. If it was not possible to remove the trace during this time, the processing can be repeated.

The product can cause skin irritation upon direct contact, therefore work with it only with gloves.

Alcohol

Alcohol is safe for metal and most coatings, so it can be safely used to remove adhesive.It works well on fresh stains. To do this, just wipe them several times with an alcohol-soaked cotton pad.

If the glue has managed to firmly adhere to the surface and become covered with dust, additional steps will be required:

• to begin with, the dried composition is cleaned with a stiff, but not iron, brush;
• soak a sponge in alcohol and apply it to the stain;
• leave to act for 30-60 minutes;
• remove the softened composition with a plastic spatula, wipe the treated area with a clean, damp cloth.

It can be replaced with vodka, but it is less concentrated, so the exposure time is doubled.

Acetone

Acetone is the most popular solvent. It is most often used to remove paintwork, but it works well on glue stains.

Mode of application:

1. Apply the composition to a cotton or gauze swab.
2. Wipe the stain with it from the edge to the center.
3. Continue processing until the glue is completely dissolved.
4. As the disk becomes dirty, it needs to be changed.
5. Treat the surface with a clean, damp cloth.

Acetone is poisonous to humans; inhaling its vapors can cause severe headaches. Therefore, you need to work with it in a respirator. To prevent the composition from being absorbed into the blood through the skin and damaging the nails, protect your hands with gloves.

If the metal is varnished or painted, you should first try applying acetone to an inconspicuous area.

Cooling

The glue easily comes off the surface when cooled, but for this the temperature must drop below minus 25-30 degrees.This can be achieved by placing the item in the freezer.

Instructions for action:

1. Wrap the product in polyethylene.
2. Place in the freezer for 6-8 hours.
3. Remove the item and carefully separate the frozen trace from the metal surface.

If the stain cannot be removed the first time, repeat the procedure. Cold is not capable of harming the metal, so the method is safe for the product.

Heat

Sticky marks are afraid of high temperatures. When they are heated above 50 degrees, the strength of the connection decreases, so the stain can be easily removed from the surface.

Metal, on the contrary, is resistant to high temperatures, so there is no risk of damaging it. You can use a hair dryer to remove the glue.

Mode of application:

• turn on the hairdryer at medium power;
• bring it to the stain as close as possible, but not too close;
• hold for a while until the composition becomes soft;
• remove it with a plastic spatula or roll it with a rubber roller;
• walk over the surface with alcohol for final cleaning.

In addition to a hairdryer, an iron can come to the rescue, but first you need to cover the stain with a sheet of cardboard. They walk over it with a hot sole several times, after which they remove the paper along with the sticky composition.

For complete cleansing, the area is treated with alcohol.. The method is effective, but when heating painted surfaces, care must be taken not to remove the protective layer along with the glue.

Anticlean

Anti-glue is a composition that is used to remove sticky marks from various surfaces. The gel is available in small tubes of 5 mg. The product costs from 80 to 100 rubles.

Instructions for use:

• apply gel to the stain;
• cover the surface with a napkin;
• leave for 10-12 hours;
• Remove the softened mixture with clean paper.

How to clean with professional cleaners?

In addition to improvised means, you can use professional removers to remove glue. The most popular brands:

1. Spray Prosept Duty Universal (350 rubles for 0.4 l). The solvent is sprayed onto the stain for 1-2 minutes (5-10 minutes for hardened compounds). Residues are removed with a rag.

   The product is easy to apply and is suitable for removing all types of glue, actively dissolving their base.

2. HG for removing glue (360 rubles for 300 ml). The liquid is applied to the stain, left to act for 15 minutes, and the residue is removed with a cloth. This composition can cope with both fresh and old stains.
3. Tesa spray cleaner 200 ml (520 rubles for 200 ml). The composition is sprayed onto the stain, left for 5 minutes, and removed with a napkin. The spray is easy to apply, it does not contain chlorine and silicone, it is used very economically, and has a pleasant smell.

All formulations can be purchased at a household chemical store or ordered online.

Helpful information

Tips to help deal with stains from glue without harm to the product:

1. Metal should not be cleaned with other metal products with sharp edges, such as a knife or spatula. This will cause scratches.
2. If the metal is covered with paint that is damaged, the use of solvents should be abandoned. They will make the situation worse.
3. After treating the surface with any substances, it must be wiped with a cloth soaked in clean water. Solvent should not be left on metal.
4. The composition must be applied precisely, trying not to get on a surface free of glue.

Video on the topic

Methods for removing sticker adhesive from a metal surface are presented in the video:

Conclusion

Removing sticker adhesive from metal is not difficult if you choose the right product. The longer the stain remains on the product, the more aggressive the composition must be to remove it. In addition to available substances, you can purchase professional removers, or resort to heat treatment.