What is the reason that the Whirlpool washing machine does not spin, what should I do?
The lack of spin in the Whirlpool washing machine is a reason to diagnose the equipment. Once the faulty area is identified, repairs may be necessary.
But in some cases, the problem lies in user errors, and you can solve it on your own, without involving a specialist.
What are the reasons why the Whirlpool washing machine does not spin clothes, and how to fix this problem, we will tell you further.
Content
Why doesn't the spin cycle of my Whirlpool washing machine work?
The lack of spin or its insufficient quality may be indicated by high humidity of items after washing or water remaining in the drum. At the same time, the Whirlpool machine itself may make sounds uncharacteristic of normal operation, vibrate, or not spin at all.
There are several reasons for the lack of a full spin. The most common ones include the following:
A blockage in the drainage system occurs when water cannot physically be drained from the tank, and spinning as such becomes impossible.- Problem with the level sensor. If it breaks down, the signal from the control module to drain may simply not be received.
- Motor failure. This almost always leads to a drop in power, and, as a consequence, the inability to wring things out.
- Control module failure.
- Tachogenerator failure.
- User errors.
- Malfunctions in the operation of the pressure switch.
- Belt slippage.
- Pump failure.
- Bearing wear.
- Wear of shock absorbers.
It may be necessary to sequentially analyze the status of the affected nodes to pinpoint the cause of the failure.
Diagnostics and repair
Starting to diagnose the condition of the equipment? It’s more convenient to start by inspecting components that have easier access, and which can be carried out even without disassembling the Whirlpool device. First, we exclude user errors.
Analysis of the selected mode
One of the most common problem situations is the wrong choice of washing mode.. If a cycle was set according to the “no spin” program or with a spin at low speeds, then the items may remain wet after they are removed from the drum.
Imbalance of things in the drum
When washing one item or items that are too bulky, or when the laundry gets bunched up, the washing machine cannot evenly distribute all the laundry. The way out of the situation is to put things away and repeat the launch.
Overload of laundry
This is another common user mistake. When you put a lot more stuff into a Whirlpool drum than it was designed for.
If the laundry is overloaded in the drum, the washing machine technically cannot spin it out as necessary.
The solution to the problem is to put some things away from the machine and repeat the spin cycle.
Drain pump failure
The drain pump is responsible for pumping water out of the tank.. If it is damaged, then the water cannot be drained from the washing machine and it continues to remain in the machine.
For accurate diagnosis, it is necessary to gain access to the part. If a breakdown occurs, the pump is replaced.If it is clogged, it may be enough to simply clean the unit.
No drainage due to blockage
The inability to drain water from the tank after washing may be due to several reasons. This could be a blockage in the sewer system or in the components of the Whirlpool washing machine itself (pump, filter, pipes, hose). For diagnostics, partial disassembly of the washing machine may be necessary.
You can watch the video on how to clean the filter:
Engine brush wear
Electric motor brushes are parts that, with prolonged use of the Whirlpool, gradually wear out and decrease in size. In such a situation, the device does not reach speed, and there may be sparking and contact closure.
The situation cannot be ignored, as over time it will only get worse, and the washing machine will not only not cope with spinning, but also with washing.
Drive belt jumping/slipping
In Whirlpool washing machines, the rotation of the drum is driven by a drive belt connected to a motor. If the belt is stretched and slips during rotation, spinning at high speeds does not occur.
To assess the condition of the belt, open the back cover of the washing machine and inspect the part.. If the belt slipping off the pulley is a one-time situation, it must be returned to its place by throwing it over the pulley and turning the wheel. But when the situation repeats or the belt does not fit tightly, it needs to be replaced. A new belt is selected taking into account the specific model of the washing machine.
How to choose a belt and replace it is shown in the video:
Tachometer malfunction
If the Whirlpool does not spin the drum at all or only rotates weakly, the problem may be in the tachometer. This unit is responsible for controlling engine speed. If it breaks, the drum does not accelerate to the speed specified by the program. The solution to the problem is to replace the part.
Control block
If the radio elements on the Whirlpool control unit are burned out or the contacts are broken, high-quality repairs are necessary. The module is removed, diagnosed and repaired. This type of work requires experience and good tools, so it is advisable to trust such repairs to professionals.
Shock absorbers
Shock absorbers in a Whirlpool washing machine are responsible for stabilizing the position of the tank in the washing machine body, including under heavy load.
When the shock absorbers wear out, the device begins to vibrate strongly and a knocking sound is heard., and the machine itself can jump and move.
This situation leads to the fact that a full spin becomes impossible. The way out of the situation is to partially disassemble the washing machine and replace the shock absorbers.
Bearings
The bearing assembly begins to suffer when water passes through the seal. Loss of tightness leads to water getting onto metal parts. As a result, the bearings rust and the lubricant is washed out.
If there is a problem with the bearings, the Whirlpool washing machine knocks loudly during operation. In this case, spinning either does not occur at all or is very weak.
To make sure there is a problem, you need to remove the back wall of the washer. This will allow you to see the tank. If the bearings are worn out, there will be rust marks on it. In advanced cases, rusty stains may also appear on laundry placed in the drum for washing.
Motor failure
If the motor breaks down, your Whirlpool washing machine may stall without spinning. To diagnose the condition of the motor, it is removed. If possible, repairs are carried out. Otherwise, replacement is required.
Pressostat
The water level sensor transmits information to the control module. If the device makes several revolutions, but still does not squeeze out the water, the problem may be in the pressure switch. The sensor transmits incorrect information or does not respond to signals at all. The solution to the problem is repair or replacement, depending on the condition of the part.
Call the master
It is not always possible to carry out high-quality diagnostics, much less professional repairs, on your own. In this case, you need to contact a washing machine repair company and call a technician.
The cost of the work depends on the complexity of the breakdown and the price list of services. On average in the capital for Whirlpool repairs, prices start from the following indicators:
replacement of the pressure switch – from 1,600 rubles;- electric motor replacement – from RUB 2,000;
- replacement of shock absorbers - from 2,200 rubles;
- repair of the control module - from 2,000 rubles;
- replacement of the drive belt – from RUB 1,000;
- replacement of motor brushes – from RUB 1,500;
- clearing the blockage – from RUB 1,200;
- pump replacement – from RUB 1,600.
New replacement parts will be charged separately.
Conclusion
If the Whirlpool washing machine does not spin, there may be many reasons. Having identified the problem unit, it is necessary to carry out repairs, and companies that specialize in servicing household appliances can help with this.
