A matter of technology, or how to disassemble a Samsung washing machine with your own hands

Samsung washing machines are reliable and durable household appliances, but there are simply no devices that would never fail.

If a breakdown occurs, parts need to be replaced, and for this the Samsung washing machine needs to be disassembled.

For information on how to properly disassemble and reassemble a Samsung washing machine, read the article.

Preparing for disassembly

Before you begin the main procedure, you need to perform several preparatory steps.

They include 3 main stages:

1. Take the device out of the bathroom, as it is very difficult to disassemble it in a narrow room. In addition, the room should be well lit. The area of ​​upcoming work should be covered with rags or newspapers so as not to spoil the floor covering (if the work is planned to be carried out in an apartment).
2. Prepare tools.
3. Prepare the device itself for upcoming repairs.

To completely disassemble the washing machine, You will need the following set of tools:

• screwdrivers or screwdriver;
• wrench and hex key;
• pliers;
• multimeter;
• hammer;
• colored markers;
• WD-40 lubricant;
• sealant;
• rag.

Sometimes it becomes necessary to cut the tank, for example, to gain access to the cross. In this case, you cannot do without:

• hacksaws,
• drills,
• drill,
• self-tapping screws and bolts.

Preparing the machine itself involves going through the following steps:

1. Turn off the power to the device. It is unacceptable to disassemble a machine connected to the mains.
2. Disconnect the water fill and drain hose.
3. Remove the drain filter and drain the water in it. If it is dirty, it can be cleaned.
4. Place the device in a convenient place.

After all the preparatory work is completed, you need to study the diagram of the washing machine. You can learn how a Samsung washing machine works from this articles.

Samsung washing machine circuit diagrams

The design diagrams of Samsung washing machines may have slight differences, depending on the model. However, the general components are always the same. The diagram is shown in the figure:

Essential elements Samsung washing machines:

• the front panel, back wall, top cover and bottom of the device are all fixed with bolts;
• pull-out tray for detergents;
• program panel;
• drum, coupling, tank;
• counterweights - most often there are two of them, they are located in the upper and lower parts of the washing machine;
• engine;
• springs;
• pump;
• heating element;
• pressure switch

In addition to the basic circuit of the washing machine, There is also an electronic circuit that is useful when checking the integrity of wires and components. It is shown in the figure:

Process Features

Depending on the type of load, the methods for disassembling washing machines will differ. If the procedure is performed for the first time, you must strictly follow the instructions so as not to damage the device.

Front loading automatic machine

Disassembly must begin by removing the top cover. To do this, unscrew the 2 screws that are located on the back wall of the device. The lid is moved back 15 cm and lifted.

Further algorithm of actions:

1. Removing the hopper and control panel. First you need to remove the detergent dispenser hopper. To do this, you need to press the latch located at the base of the hopper and pull the container towards you again. It will come out easily, no special effort is needed. Behind the hopper you can find fasteners holding the control panel. They are unscrewed: there are 2 screws in front and 1 screw is on the right. Separate the panel using a screwdriver, prying it off from the left side.
2. Removing the front panel. You need to pull it by the bottom edge to release it from the top latches. Then the panel is carefully pushed towards itself, but without sudden movements. You can find a lot of wires at the back. You need to pull them out one at a time by snapping the latches.
3. Removing the bottom panel. It is secured with 3 latches. It is convenient to pry it off with a slotted screwdriver by inserting the tool into the existing slot. First, it is pushed away in the center, and then along the edges, after which the panel easily comes off.
4. Removing the front panel on which the door is located. It is fixed with 2 screws on the bottom and 2 screws on the top. They are being twisted. As a result, the panel will be held on small hooks.
5. Removing the seal. If you open the door, you will find that it is connected to a rubber part. The fixing ring of the cuff is picked up with a flat screwdriver and slightly pulled towards you.

   Behind it there will be a tightening metal clamp in the form of a spring. You need to find its latch and unlock it using a flat-head screwdriver.

   Then they pass it around the entire circumference of the ring to disconnect it. You need to work with the tool carefully. Otherwise, the torn cuff will have to be replaced.

6. Removing the rear panel. This process will not be difficult. It is enough to remove the 4 screws that secure it.
7. Disconnecting hoses. They lead to the machine tank (fill and drain), to the pressure switch and to the powder tray.
8. Disconnecting the wires leading to the heating element and temperature sensor. The heater itself is located in the front lower part of the tank, under the drum. To remove it, you need to unscrew the nuts. After this, the heating element will easily come out of the socket. When removing the wires, you need to mark their location with colored markers.
9. Dismantling counterweights. There are 2 of them in the washing machine: above the tank and below it. They are fastened with bolts. Since the loads are heavy, they must be removed carefully.
10. Help will be required to remove the tank. It's difficult to handle with just one pair of hands. First you need to disconnect the shock absorbers, and then carefully remove the tank from the springs and pull it out. After this, remove the belt and motor. Finally, remove the pulley by unscrewing the middle bolt. If it is rusty, lubricate it with WD-40.
11. There are bearings inside the drum. To remove them, the tank must be disassembled. If it is soldered, it is sawed with a hacksaw. This process is very labor-intensive and not all craftsmen undertake such work. In this case, it is easier to purchase a new drum. Provided that the tank is collapsible, replacing the bearings will not be difficult.

From vertical

It is more difficult to disassemble a top-loading machine. Such devices are rarely found in Russia.

The procedure is as follows:

• unscrew the screws located on the sides;
• move the block in your direction;
• disconnect all wires;
• remove the washing machine panel.

Further disassembly of the device is carried out in the same way as a front-loading washing machine: remove the tray, panels, and clamp.The process is completed by removing the drum, replacing or repairing failed parts.

How to assemble?

Assembling a Samsung washing machine is not difficult if you photograph all the steps. Installation is carried out in reverse order.

Be sure to secure all wires and hoses. When screwing the parts, you need to check that they do not dangle, but are securely fastened.

Possible difficulties

While disassembling the washing machine You may encounter the following difficulties:

1. The wiring is broken. When working with wires, you need to act carefully, as they are very fragile. If a break occurs, replace the damaged element.
2. The integrity of the cuff was compromised. To prevent this from happening, you should not try to remove it with sharp parts, such as a knife. Use a screwdriver carefully.
3. The bolts have broken. If they are difficult to unscrew, you need to resort to WD-40.
4. The pipes or pulley are broken.

To avoid minor troubles and additional expenses, you need to disassemble the washing machine carefully, slowly and trying not to damage the parts.

All about repairing Samsung washing machines - in this section.

Video on the topic of the article

How to disassemble a Samsung washing machine, video instructions:

Conclusion

Disassembling a Samsung washing machine is not an easy task, but you can cope with it if you approach the matter responsibly.

Do not break the sequence of actions, to clarify the location of the parts you need to use a diagram. The entire work process must be recorded so that you can easily assemble the device later.