Drum

The drum of a Samsung washing machine is the basic part of this household appliance. Without it, the operation of washing equipment is impossible.

In the article we will look at the structure and purpose of the drum of a Samsung washing machine, the main reasons for its breakdown, how to eliminate them, as well as the features of cleaning and calibration.

Device and purpose

The drum of a Samsung washing machine is one of the main parts, since it is in it that the laundry is loaded. A cross with a shaft is attached to the back of the drum, which transmits rotation to the drum from the motor.

There are loopholes inside the part - These are special pads that mix laundry during washing. The strikers can be straight or curved.

The surface of the part is covered with small holes - perforations. They differ depending on the model of the washing machine, but their purpose is always the same - the washing solution flows through them. However, they are the ones who cause premature damage to things.

Samsung washing machine manufacturers are striving to solve this problem, so they have developed devices with a unique Diamond Drum design, in which the holes are located in the center of pyramidal recesses, shaped like diamonds.

Thanks to this decision, fabric under the influence of centrifugal force does not penetrate into the holes and is not damaged. At the same time, the quality of washing remains high.

In modern appliances, not only soapy water, but also steam is supplied through holes in the drum.

Causes of failure

Despite the fact that manufacturers of Samsung washing machines pay enormous attention to the quality of their equipment, the possibility of breakdown cannot be ruled out.

Doesn't turn

The drum may stop rotating for a number of reasons. Among them:

• overload of laundry;
• belt breakage or slippage;
• wear of motor brushes;
• bearing wear;
• failure of the control board;
• broken wiring.

If reducing the load on the appliance in the form of removing some of the laundry did not help solve the problem, most likely the cause lies in a more serious breakdown. Read more in this article.

Why is it knocking?

The sound of a drum is not normal, but there is no need to panic. First you need to think about what was loaded into the device. Perhaps the unusual sound is the result of the interaction of the metal wall of the drum and some parts of the clothing: plastic or metal.

If this cause has been ruled out, the following issues need to be considered:

1. There is a foreign object between the tank and the drum (coin, button, bra wire, etc.). The foreign body must be removed, which will require disassembling the washing machine.
2. The surge protector that is attached to the back wall of the machine has come off. It hits the tank, causing a knocking noise. It is necessary to disassemble the equipment and check the quality of fixation of the part.
3. The shock absorbers have failed. If they have lost their elasticity and stretched, then when they sink to the bottom, they will begin to make a characteristic knock on the body of the device.It may sound like a drum is beating. The problem can be solved by replacing all shock absorbers.

Creaks when washing or spinning

If you hear an iron squeak, then the bearing is highly likely to have failed.

This occurs during prolonged use of the device and is a natural process. Over time, all parts wear out. To get rid of the squeak, you need to disassemble the drum, replace the bearings and seals.

Another reason for squeaking is when parts of items that are in the wash get on the hatch cuff. Sometimes squeaking is caused by fur or hair that has bunched up in a ball.

A slipping drive belt and a weakened shaft mount respond with a creaking sound.. In this case, you need to disassemble the washing machine and fix the problem.

A common cause of squeaking is bearings that are worn out, but not completely. It is better to replace them in the near future, or the machine may fail at the most inopportune moment.

There is water in it

If there is water in the drum and does not drain, this may be due to the following reasons:

1. There is a blockage in the drain filter. It can be formed by any small objects. To deal with the problem, you need to clean the filter and put it back.
2. The pump is broken or clogged. If no dirt is found in it, the part needs to be replaced.
3. The control board has malfunctioned. Sometimes simply rebooting the device helps. It is enough to turn it off for 15 minutes and then start it up again. If this does not help, repair is required.

How to replace a part on a Samsung washing machine?

To replace the drum, the washing machine must be disassembled. First, twist the top panel and the parts underneath it.

Then they move on to the control panel, front wall and cuff. Be sure to remove the counterweights and disconnect the wires. Having gained access to the drum, it is removed.

It is difficult to cope with the task alone, so you need to make sure that there is an assistant nearby.

After the broken part is dismantled, a new set is installed in its place. The procedure is performed in reverse order. To avoid confusion, you initially need to record the entire analysis process on a photo or video camera.

To learn how to remove the drum from a washing machine, read this article about replacing the crosspiece - in this.

Calibration

The Samsung washing machine independently determines the weight of the items loaded into it. To make this value more accurate, you need to run the calibration mode.

This is done in several steps:

1. Switch off the device and empty it.
2. Press the “Temperature” and “Delay End” buttons simultaneously, and then “Power”. The device should turn on.
3. Click on the “Start” button, this will activate the calibration mode.
4. The drum will begin to rotate clockwise and counterclockwise. The whole process takes about 3 minutes.
5. When it stops, “End” will appear and the device will turn off.

After calibration, the equipment is completely ready for washing.

Cleaning

One of the innovative features of modern Samsung washing machines is Eco Drum Clean.It allows you to remove odors and dirt caused by bacteria that accumulate on the walls of the centrifuge.

To get rid of them, there is no need to buy expensive detergents. Washing The machine itself displays information on the screen that it is time to clean the drum. The owner of smart technology will only have to select the appropriate function and launch it.

If the model is outdated, then you will have to clean the drum yourself. This requires chlorine bleach and powder, which are placed directly into the spinner and run on a high-temperature wash cycle. Read more Here.

Where and how much to buy a new one?

You can buy a new drum from an official Samsung dealer. The average price of a part varies from 5,000 to 10,000 rubles. If you change it yourself, the expenses will be over. If you contact a master, you will have to pay about 3,000 - 5,000 rubles, depending on the complexity of the work.

If you still decide to buy a new part, then you need to be extremely careful when placing your order. The drum must match the washing machine model. This is indicated in the accompanying documentation. You need to buy a drum complete with a cross..

Call the master

Replacing a drum costs at least 3,500 rubles, excluding expenses for the part itself. Work completion time is from 1 to 3 hours. The average warranty period is 1 year.

When calling a specialist, you need to contact proven specialists. It is recommended to give preference to repairmen from a large company that has its own website and office in the city.

To minimize the risk of encountering scammers, you first need to study reviews about the company on the Internet. Contacts of masters can be found on the Internet or in newspaper advertisements.

Conclusion

The drum of a Samsung washing machine rarely fails. If this happens, you need to try to find the cause of the breakdown and fix it yourself. When you can’t cope on your own, you should contact a specialist.