Errors

Bosch washing machines are distinguished by sophisticated electronic intelligence.

The equipment not only copes well with its main task - washing dirty clothes, but can also tell you which part is out of order or is not functioning correctly.

In this case, an error code will be displayed on the display of the Bosch washing machine. Read the article on how to decrypt and fix it.

Decoding codes for Bosch washing machines with display

Error codes appear on the screen if the washing machine malfunctions. Their correct interpretation is the key to successful and quick troubleshooting.

F00, E00

Codes F00 and E00 mean the same thing. Most often, they appear on the screen immediately after turning on the device and indicate that there is a failure in the firmware of the control board.

Causes and solutions to the problem:

• one-time electronics failure - a reboot is required, turning off the device for 15 minutes;
• software failure due to power surges - memory chip reprogramming required;
• failure of the electronic module - it is either repaired or replaced.

E02

Code E02 indicates problems with engine operation. In this case, the machine will either stop rotating the drum altogether or stop the wash without allowing the cycle to complete.

Causes and solutions:

1. The motor contacts have come loose.This may occur due to excessive vibration, improper installation, or transportation. The terminals must be returned to their place.
2. There is no voltage in the network. You need to wait until the power supply is restored, after which you continue washing.
3. One-time board failure due to power surges. The device needs to be rebooted.
4. Worn out brushes. They are consumables and therefore require replacement.
5. The motor is broken. It needs repair or replacement.

Details - in this article.

E67, F63, F67

Codes E67, F67 and F63 indicate a malfunction of the control module. In this case, the device will not respond to button presses, will not launch programs, and will not erase things.

Causes of failure and ways to eliminate it:

• a one-time failure in the operation of the control board - the machine must be rebooted and turned off for 20 minutes;
• faulty wiring - the wires have either come loose or been damaged, for example, by rodents;
• control board failure due to defective or network failure - it requires repair or replacement.

E01, F34, F36, F61

Codes E01, F34, F36, F61 occur when it is not possible to close the washing machine hatch. In this case, the wash does not start, and the “lock” icon flashes on the display.

Causes and solutions:

1. The cuff is bent, which prevents the door from closing. It needs to be straightened out.
2. Things got into the gap between the hatch and the tank. You need to open it and remove the foreign object.
3. Check the hatch latch. Sometimes there is a mechanical obstacle that prevents closure.
4. UBL is broken. It needs to be replaced.
5. The control board has malfunctioned. The machine needs to be rebooted.

F02

Code F02 appears when there is no water flowing into the washing machine. In this case, the washing does not start, and 5 minutes after starting the program, the device turns off.

Causes and solutions:

• The water supply tap is closed and needs to be opened;
• the inlet filter is clogged - this often happens after turning off the water, when a lot of foreign impurities appear in it, the mesh needs to be checked and cleaned - it is located at the back of the device, at the place where the hose is attached;
• low pressure in the water supply - this problem is more typical for the private sector;
• failure of the control board - the machine needs to be rebooted;
• The water supply hose is pinched and needs to be checked;
• the water supply valve is broken - it cannot be repaired, it must be replaced;
• The water level sensor has failed - the pressure switch needs to be cleaned of debris or replaced; it cannot be repaired.

F03, F18, E18

Error code F03, F18 or E18 is displayed on the screen if there are problems during the draining process. It appears when the drain should have started, but the water does not leave the drum for 10 minutes.

Causes of the problem and ways to solve it:

1. The drain filter is clogged. It needs to be cleaned. The filter is located at the bottom of the machine, under a small hatch.
2. A clog has formed in the sewer pipe, causing water to not flow through. It needs cleaning.
3. The drain hose is clogged. It needs to be removed and washed.
4. The washing machine is installed on an uneven surface. Her legs need to be adjusted to the level.
5. The drain pump has failed. pump can be repaired or replaced.

Details - in this article.

F04, F31

Code F04 indicates that the device has detected a leak. In this case, a puddle will be visible under the machine after washing. The water itself can remain in the tank.

Causes and solutions:

• the leak is concentrated in the area of ​​the powder receiver and the water supply valve - it is necessary to check the tightness of their connection, which can be broken due to excessive vibrations;
• the drain filter is clogged, causing some of the water to fall onto the floor;
• the drain hose is leaking due to a loose connection with the pump;
• damaged hatch cuff — you need to check its integrity.

F16 and E16

Codes F16 or E16 indicate that the machine cannot lock the hatch door due to a problem in the circuit. In this case, the wash does not start, the lock blinks.

Causes and solutions:

1. The door does not fit tightly to the hatch; something is in the way.
2. The control board has malfunctioned and the device needs to be rebooted.
3. Damage to the UBL, contacts or wiring at its connection to the control module. The part needs to be replaced or repaired.
4. The hatch hinges were frayed or broken due to improper use of the device, for example, a child was riding on the door. Another possible failure is a skewed tongue in the lock. The lock or hinges need to be replaced.

Details - in this article.

F17 or E17

Codes F17 or E17 indicate that water has not filled into the drum for the allotted period of time. In this case, the door may remain locked.

Causes of the malfunction and ways to eliminate it:

• The drain hose is not connected correctly, causing water to constantly flow into the sewer;
• there is no water, the supply tap is turned off, or the inlet hose is pinched - you need to check the condition of all elements;
• the water supply valve is clogged - it needs to be cleaned;
• The filling valve is broken and requires repair;
• the water level sensor has failed - you need to try to clean its tube or replace the sensor;
• If the control module malfunctions, the machine will have to be rebooted.

Details - in this article.

F19

Error code F19 appears when the water is not heated. In this case, the device does not start washing and may not respond to commands.

Causes and solutions:

1. The program crashed. The equipment needs to be rebooted.
2. No heating mode selected. You need to look at the settings.
3. Scale has formed on the heating element, causing its performance to deteriorate. The heating element needs to be cleaned.
4. The heating element has burned out. It will not be possible to repair it; the broken part will have to be replaced.
5. The temperature sensor is broken. It cannot be repaired and requires the purchase of a new part.
6. The heating element contacts have oxidized or the wires have been damaged. The contacts are cleaned, the wiring is changed.

F20

Code F20 appears on the display of the Bosch washing machine if the water heats up, but this was not provided for by the selected program.

Causes and solutions:

• there was a failure in the operation of the control module - the device requires a reboot;
• The timer or temperature sensor is broken - the elements must be replaced;
• The heating element is faulty - it needs to be inspected by a technician, perhaps the part can be repaired.

F21, F43

Codes F21 and F43 appear on the display if the drum stops rotating. This error occurs when the liquid has been filled and the wash cycle has started. The motor may stop altogether, or will make jerky movements.

Causes and solutions:

1. The socket or plug is faulty, causing the power supply to be interrupted. There may be a burning smell. The power needs to be turned off and the outlet needs to be repaired.
2. The network voltage is low or unstable. Most often, this situation occurs in private homes.
3. The washing machine froze. It needs to be rebooted and turned off for 10 minutes.
4. The motor brushes are worn out. They need to be changed.
5. The tachometer, which determines the rotation speed of the motor, has failed. They are changing it. It is located on the rotor.
6. The motor has shorted out. Repairs are carried out depending on the type of breakdown.
7. A foreign object has gotten into the tank, for example, a wire from a bra, a pawl from a lock, etc. The tank will have to be disassembled to remove debris that is interfering with its rotation.
8. Bearings are worn out. The complete stop of the drum will be preceded by a strong rumble and noise. Bearings cannot be repaired.
9. The power cord or plug is frayed. Due to their wear, the circuit closes, which leads to power outages. Chain ringing required. Based on the results, faulty elements are repaired or replaced.

Details - in this article.

F22, F37, F38

Codes F22, F37, F38 indicate a breakdown of the temperature sensor. In this case, the machine does not heat the water, even if this process is provided for by the program.

To deal with the problem, you can try to reboot the device by disconnecting it from the power supply for 15 minutes.

If this does not help, the condition of the heating element should be assessed. If it is operational, inspect the temperature sensor. If it breaks, the part is replaced.

F23 or E23

Codes F23 or E23 indicate that the Aquastop leak protection system is activated. Causes and solutions:

• there is an excessive amount of foam in the drum, which occurs when the detergents are selected incorrectly, when the dosage is calculated incorrectly, or when washing porous clothes - in this case, the water must be drained in emergency mode and the cause that led to the formation of a significant amount of foam must be eliminated;
• the Aquastop sensor has triggered due to a cuff break, or due to a clogged drain filter - the filter needs to be cleaned, and the cuff must be turned upside down;
• The microswitch of the Avkastop system is broken - a complete replacement of the structure is required.

Details - in this article.

F25

Code F25 appears when the water level sensor is broken. Causes and solutions:

1. Lime has accumulated on the sensor and needs to be cleaned.
2. The water in the tank is really cloudy. It needs to be drained, and then run a washing program at a temperature of 90 degrees. The machine must be empty.
3. The turbidity sensor has failed. This kind of breakdown is rare, but sometimes it does happen. A part needs to be replaced.

F26 and F27

Codes F26 and F27 appear when the pressure sensor breaks down. In this case, the washing machine will not draw or drain water.

Causes and solutions:

• control board failure - the device needs to be rebooted;
• the pressure sensor has failed, or the wires running between the board and the sensor have broken - repair of the identified fault is required;
• The pressure switch is broken - it is either cleaned or replaced.

F28, F29, F60

Codes F28, F29, F60 indicate a malfunction of the water flow sensor. In this case, liquid will not flow into the drum of the washing machine.

Causes and solutions:

1. There was a malfunction in the operation of the equipment. To normalize the execution of programs, you need to disconnect the machine from the power supply for 20 minutes, and then start the washing cycle again.
2. The water flow sensor is broken. The part cannot be repaired and must be replaced.
3. The water supply valve is clogged or faulty. It is necessary to inspect it and solve the problem, depending on its origin.

F40

Code F40 indicates a power supply error. In this case, the washing machine will either not turn on or stop responding to commands.The causes of this malfunction do not require repair of household appliances.

F42

Code F42 indicates that the engine motor is spinning too fast. In this case, accelerated rotation of the drum and excessive vibrations are observed.

Causes and solutions:

• malfunction of the electronic module - to correct the machine you need to restart;
• assess the condition of the tachometer - if it is faulty, it must be replaced;
• inspect the motor and its wiring - if the engine elements are subject to repair, then they are partially replaced, in other cases the motor must be replaced completely.

F44

Error code F44 indicates that the motor does not rotate in the opposite direction. In this case, the washing stops and the programs do not work.

Causes and solutions:

1. Control board failure. To normalize the operation of the device, it needs to be rebooted.
2. Failure of motor components such as a triac or reverse relay. The parts are replaceable, so there is no need to repair the entire motor.

F59

Code F59 indicates a 3D sensor data error. In this case, the device will not finish washing things. First you need to try to restart the machine. If this does not help, then evaluate the condition of the 3D sensor and the wires leading to it. If a malfunction is detected, it is eliminated.

What does error E32 mean on a Bosch washing machine? here.

Malfunctions and their designations on household appliances without a display

Older models of Bosch washing machines do not have a display. However, they also know how to send signals indicating a malfunction of a particular part. This is done in the form of a set of light signals. Depending on the breakdown, one or another indicator will flash.

The main codes are presented in the table:

Yes – the indicator blinks. No – the indicator is not lit.

Bosch washing machine repair cost

If it is impossible to cope with the breakdown on your own, you need to seek help from a specialist. The price for a master’s services will vary depending on the region and place of his work. Repairs at service centers are more expensive than those done by private specialists.

Approximate prices for main types of work are as follows:

1. Control board repair, flashing a memory chip - from 2000 rubles.
2. Replacing the motor – about 3500 rubles. Repairs will cost less, about 1,500 rubles.
3. Replacement of UBL – 1600 rubles.
4. Replacement or repair of a pressure switch – from 1600 rubles.
5. Replacing the heating element – 1800 rubles.
6. Replacement of the Aquastop system - from 2500 rubles.
7. Replacing bearings – from 4100 rubles.

You can find a specialist by looking at an ad in a newspaper or on the Internet.Before calling a specialist to your home, you need to study the reviews that are left on third-party resources. Work is paid only upon completion of it.

Prevention of breakdowns

To minimize the likelihood of a malfunction of your Bosch washing machine, you need to adhere to the following recommendations:

• do not allow cables, wires and hoses to be pinched;
• use powders labeled “automatic” and dose them correctly;
• check pockets before putting clothes in the wash;
• use voltage stabilizers;
• Clean the drain filter at least once every 3 months;
• use descaling agents.

Conclusion

Deciphering the error code is a simple task that you can handle on your own. Most often, the problem can be resolved by simply rebooting the device. If the breakdown is serious, you cannot do without the help of a specialist.