Practical recommendations on how to remove the brush from a Samsung vacuum cleaner for cleaning or replacement
The brush of a Samsung vacuum cleaner is one of the main structural elements, without which the operation of the device is impossible. With its help it is convenient to collect dust from carpets and other coverings.
Most models come with several attachments that make cleaning more efficient and better. To replace, you need to remove one brush from the pipe and install another.
It is at this stage that some users experience difficulties. We'll tell you in this article how to remove the brush from a Samsung vacuum cleaner.
Content
Removing a structural element of a Samsung household appliance
The brush from the Samsung washing machine is removed manually. For the sake of curiosity, you should not do this, so as not to loosen the inlet.
It is removed in pursuit of certain goals:
- Replacing one brush with another, for example, from a carpet brush to a furniture brush or to a crevice brush.
- Cleaning a brush that is clogged with debris.
- Disassembling the brush to replace wheels or remove dirt.
- Replacing a broken nozzle.
To disconnect the nozzle from the pipe, proceed as follows:
Disconnect the device from the network.- Take hold of the upper part of the brush with one hand, which overlaps the pipe.
- With your other hand you need to hold the pipe close to the place where it connects to the nozzle.
- Using gentle twisting movements, pull the pipe and brush in different directions.
You need to scroll 45 degrees, then return it and turn it again, continuing to pull the nozzle down. In 2-3 approaches it will be possible to remove it.
Some models of Samsung vacuum cleaners are equipped with a button located on the nozzle. To remove it, you need to press the key. The latch will open, after which the brush will be in your hands.
Sometimes it happens that the brush gets jammed and removing it from the pipe becomes problematic. In this case, simple tips can help:
- heat the nozzle using warm air from a hair dryer;
- keep the joint under running hot water;
- After removing the brush, the pipe must be wiped of moisture so that it does not rust.
How to clean?
You need to clean the brush of your Samsung vacuum cleaner regularly. Being clogged with garbage, it copes with its responsibilities worse. The suction power decreases when hair, wool, or small objects get inside.
To clean it, you need to do the following:
- Remove the nozzle from the pipe.
- Divide it into two parts. Depending on the model, this can be done in two ways: tighten the retaining screws with a screwdriver or press the latch that secures the halves.
- Use your hands to pick up and remove large debris.
- Use a toothpick to work out small holes, remove lint and clumps of dust.
- Wipe the nozzle with a damp cloth or rinse with warm water.
- You need to pay attention not only to the brush itself, but also to the place where it connects to the pipe. Sometimes this is where debris collects, preventing normal dust absorption.
- Dry it and reassemble in reverse order. To make it dry faster, you can lay it out in the sun.
- Check the reliability of all fastenings.
If the brush is not clogged too much, then preventative cleaning is enough. To do this, remove it from the pipe, turn it over with the bristles up, and remove debris from it.Using a screwdriver or a thin brush, clean the inlet hole. This procedure should be carried out after 4-5 times of using the device, and even more often if there are pets in the house.
How to disassemble the brush from a Samsung vacuum cleaner to clean it, will tell you this article.
How to disassemble and clean the brush - in the video:
How to change?
To replace the brush of a Samsung vacuum cleaner, you need to remove it by pressing the button or manually disconnecting it from the pipe. If it is faulty, it is thrown away without first cleaning it.. A new nozzle is installed in its original place.
When the classic brush just needs to be replaced with a crevice brush, it is removed and cleaned. This will save time on removing debris in the future. A new nozzle is installed in the vacant space, after which the equipment is used for its intended purpose.
How to remove the wheels?
To remove the wheels from the vacuum cleaner brush, proceed as follows:
- disconnect the brush from the pipe;
- turn it upside down with the bristles;
- small grooves can be seen in the center of the wheel;
- insert tweezers or a thin flat screwdriver into it and turn it to the side 180 degrees - this way you can remove the plastic covers, after which the wheels can easily be removed from the brush themselves.
Another way to remove the wheels is to knock out the plastic valves from the inside. To do this, you first need to remove the swivel assembly connecting the brush to the pipe. They are then squeezed out with a screwdriver or finger.
Where and how much can I buy a new one?
Buy brushes for a Samsung vacuum cleaner You can go to the online market by ordering a nozzle for the desired model.. In addition, components are sold in specialized departments that deal with the retail sale of spare parts for household appliances.
Conclusion
Removing the brush from a Samsung vacuum cleaner is not difficult if you approach this issue correctly. The main thing is not to apply excessive force and follow the instructions. Regular maintenance of the vacuum cleaner and timely replacement of components will extend the life of the device.
