Several life hacks on how to remove water from under the protective glass of a phone or smartphone

foto29337-1 Water that gets under the protective glass spoils the appearance of the smartphone. Normally it shouldn't be there.

The display is the main working area of modern gadgets; the presence of moisture on it can impede the operation of the sensor.

Read the article on how to remove water from under the protective glass without damaging your smartphone.

Content

Is it possible to remove moisture?
How to get rid of drops that got under the film?
If you do nothing, will the liquid evaporate?
Helpful information
Conclusion

Is it possible to remove moisture?

You can remove water from under the protective glass yourself. To solve this problem, you don’t have to hand over the gadget to a technician or buy a new screen.

The main reason for this was the drying of the glue on the protective element. Most often this happens with old glass that is glued only around the perimeter. In addition to water, air and dust can get into the cracks formed.

You should not walk around with a dirty smartphone, especially since the procedure for cleaning it is simple and does not require special skills.

How to get rid of drops that got under the film?

foto29337-2 The first way to remove water is by force. Guidelines for its implementation:

Place the device on a flat surface.
Using the back of a bank card, water is pushed to the edge of the glass and squeezed out.
Do not press the screen too hard to avoid damaging the sensor.

Sometimes moisture on the screen appears as an oily slick. Getting rid of it is even easier. It is enough to use any suction cup that is in the house. It is placed at the edge of the spot and pulled sharply upward.

If it does not disappear the first time, repeat the procedure. You can enhance the effectiveness of the method if you combine it with warming up the device using a hairdryer.

To make it more convenient to use the suction cup, a key ring is threaded into it. This will allow you to stick your finger inside and act more actively.

Sometimes water gets inside due to improper glass installation. Installation errors are eliminated as follows:

Using a needle, carefully pick up the edge of the protection and lift it;
the grip must be carried out on the side closest to the bubble;
run your finger through the accumulated water, squeezing it out;
The glass is lowered into place, pressing it to firmly adhere to the screen.

You can try to evaporate small droplets of water only with a hairdryer. It is turned on at medium power and the air flow is directed onto the glass. The heat will cause the water to evaporate. The average duration of the procedure is 10 minutes. Before using the hair dryer, the battery must be removed from the smartphone.

Another safe way to heat up your smartphone is to place it under a table lamp. In this case, you need to make sure that the device does not become very hot. A distance of 30-40 cm is considered safe. Only incandescent lamps are suitable for this method, since fluorescent lamps do not heat up.

If moisture gets not only under the glass, but also inside the smartphone, it must be disassembled, remove all visible water with a soft cloth. The device is then placed in a jar filled with rice and left overnight. This time should be enough for the cereal to absorb the liquid.

If you do nothing, will the liquid evaporate?

If there is very little water under the glass, it can evaporate on its own. However, with normal use of the gadget, this process will take a long time.You can speed it up using any game downloaded to your smartphone. During active operation, the smartphone will heat up, which will lead to evaporation of moisture.

Helpful information

Tips to quickly and accurately remove water from under the protective glass:

If you decide to use a hairdryer, you cannot turn it on at full power.
Be sure to control the degree of screen heating. The temperature should not exceed 50 degrees. If you have time, it is better to use cold air.
Do not place your smartphone on a windowsill in direct sunlight. This may cause the battery to explode and melt the plastic parts.
When peeling off the protective glass, you need to make sure that the surface underneath is perfectly clean. Otherwise, a hermetically sealed seal cannot be achieved.
You need to carefully remove the protection from your smartphone by prying it around the perimeter. If the spot is in the center, the movements should be progressive. Sudden tearing of the glass may cause the screen to break. The risk increases if there are microcracks on it.
It is not recommended to place the gadget on the battery, as this may damage it.

Are you interested in how to remove various stains from glass? Look into this chapter!

Conclusion

It is not recommended to leave water under protective glass, especially since it is not difficult to remove it; you just need to apply a little effort. To solve this problem, both mechanical and thermal methods of influence are suitable. The main thing is not to overheat the device and not to violate the instructions.