Winter helper: Patriot PS 601 self-propelled snow blower

During the cold season, snow removal takes a lot of time. A snow removal machine will help make your work easier.

The thoughtful design of the Patriot PS 601 snow blower, which guarantees operation down to -25, will appeal to the owner of a private home or commercial organization.

Technical characteristics and features of the Patriot snow blower

The compactness of the Patriot PS 601 did not prevent it from receiving main advantages large snow blowers:

• self-propelled model, equipped with 2 Winter Extreme wheels;
• 7-speed transmission - 5 forward, 2 reverse;
• auger drive gearbox with durable bronze gear;
• XTS is installed - an improved design for cutting and gripping snow.

Advantages and disadvantages

The model has a number of advantagesthat have a positive effect on the operation and service life of the snow blower:

1. 4-stroke gasoline engine, 7 hp. Unlike 2-stroke engines, a mixture of gasoline and oil is not required. Oil is added separately to lubricate the internal combustion engine, and 92 gasoline is added separately.
2. The bushing units are completely replaced with bearings.
3. Snow throw range. The manufacturer promises a distance of up to 10 m.
4. The carburetor is adapted for operation at low temperatures.Confident start of the snow blower down to -25 when stored in a cold room.
5. Each unit is tested at the factory and configured for operation. The auger is adjusted and the engine’s performance is checked.
6. The direction of snow ejection is changed by the handle.
7. Double system of steel augers - small stones are not scary.
8. Affordable price when compared with the characteristics of expensive brands.

The manufacturer is constantly working to modernize its line of snow blowers. Despite this, There are minor deficiencies in the work:

1. The air intake area in the carburetor suffers from snow dust - the simplest protection is not enough.
2. Small capture - the number of passes through the territory will increase.
3. There is no headlight for night cleaning.

Unpacking and Assembly

The compact format of the snow blower is achieved through quick assembly. According to the instructions, to prepare for the first launch after opening the box you need to:

• install the lower handle in the working position, fastening is done using locking bolts;
• The gear shift lever is installed in the receiving hole on the gearbox, the assembly is fixed with a locking ring and a cotter pin;
• the lever handle is installed in the designated place on the snow blower in the same way using a stopper and a cotter pin;
• a chute for throwing snow to the side is installed with a ring on the plate using bolts;
• the handle of the rotary chute is mounted and secured;
• The last step is to attach the right cable and adjust the tension of the cable drive of the wheels.

The final cable tension is checked after the first start, with the engine running. A detailed assembly diagram step by step is shown in the photo:

Preparing for the first launch

To start the snow blower engine for the first time you need to prepare:

• motor oil for 4-stroke engines;
• lubricant in the gearbox;
• AI-92 gasoline from a reliable manufacturer.

It is recommended to use only original motor oils and lubricants. Manufacturing plant engineers are working on the lubricant formula. This allows you to maintain the functionality of the engine and drive mechanics for a long time.

Further actions are performed sequentially:

1. The tank is filled with pure 92 gasoline - up to 3.6 liters.
2. The fuel valve switch is moved to the open position - all the way to the right.
3. The air damper lever is in the extreme left position.
4. The switch points to "ON".
5. The carburetor has an analogy to a hand pump - a primer. 5-6 presses will fill the fuel injection system.
6. The gas lever is installed in the middle.
7. The starter handle with the cord is pulled out until resistance appears. The next sharp jerk starts the engine.
8. Engine warm-up time is about 2 minutes. After this, the choke lever is moved to the right, the “open” position.

The engine stops as follows:

1. Fuel valve flap - closed position.
2. The switch is in the “OFF” position.

With the engine warm and running, check the correct tension of the snow blower control handle cable. Visually it should be slightly loosened, the handle should have a slight free play. When fully depressed, the auger and wheels are motionless. When the handle is pressed, the unit starts to move. After this check, the snow blower is completely ready for use.

After the initial start-up, the oil in the crankcase must be replaced after 5 operating hours. Monitoring the lubrication level in the gearbox - daily and always after inactivity, before starting. A typical engine oil change occurs once a season or upon reaching 50 engine hours.

Use on site

To begin snow removal work, you must complete the following steps and conditions:

• there should be no animals or people in front of the mechanism;
• The angle and zone of snow release is determined from a safety point of view. The auger is capable of picking up small stones or other traumatic objects;
• the speed is selected depending on the density of the snow cover;
• The rotation of the auger is activated by handle A, the wheel drive is turned on by handle B.

Snow is removed in low gears - 1 or 2. High gears are intended for transportation around the territory. Changing gears while moving can cause damage.

Maintenance, storage, technical inspection

Upon completion of work, the snow blower must be cleaned of snow dust and ice. Cleaning and checking the oil and lubricant levels can only be done with the engine stopped.

To ensure that the snow blower mechanism lasts a long time, It is important to follow the basic rules of use:

• original oils and pure gasoline, timely control of the level of technical fluids;
• all bolts and locking elements must be in place and firmly tightened;
• drive belts are monitored and replaced if worn;
• control and adjustment of controls is carried out before starting work.

Storage is carried out indoors. Before installing during non-working hours, be sure to:

• warm up and cool the engine to remove snow deposits, clean the auger to prevent freezing to the gripper;
• Place the snow blower away from heat sources.

Where can I buy?

The Patriot PS 601 snow blower is available for purchase through various online stores.

Inspect live and get advice on technology possible in person when visiting a branch of the CSN supermarket chains, the availability addresses of this snow blower are indicated on the company’s website.

Price

The price of the device, depending on the store, ranges from 38,299 rubles to 42,789 rubles. The total cost depends on the method of purchase (pickup or delivery), payment, and the availability of promotions in retail chains.

Owner reviews

This snow blower has real Buyers note the following advantages:

• powerful engine and snow throw range of 10 m;
• start up to -25;
• does not require physical training to operate;
• easy to assemble;
• affordable price compared to similar characteristics.

As a note, some Patriot PS 601 owners note the need to constantly monitor the condition of the tool - cleaning, tightening bolts, fluid levels.

Alternative options on the market

Approximate cost of alternative models from other manufacturers:

• Parma MSB-02-756 - 36,000 rubles;
• RedVerg RD-SB56/7 — 34,000 RUR;
• DDE ST6556 - 42,000 rub.

Video on the topic of the article

Video review of the Patriot 601 snow blower:

Conclusion

Due to its technical characteristics, the Patriot PS 601 snow blower will be an excellent assistant for the owner of a private home. The manufacturer has a large number of dealers in the regions and a wide network of service centers. Feedback on using the tool is overwhelmingly positive, which allows you to make a choice in favor of it.