A simple guide on how to remove the top cover of an LG washing machine

foto37029-1 There are many important parts hidden under the top cover of an LG washing machine. Despite the high reliability of the device, sometimes they can fail.

It will not be possible to get to them without disassembling the case. To learn how to remove the top cover of an LG washing machine without damaging the device itself, read the article.

Content

Preparation
Removing a structural element
- From a horizontal loading washing machine
- From vertical
How to put it back?
Possible difficulties
Conclusion

Preparation

Before you begin removing the cover, need to prepare a workplace. To do this, the washing machine is moved away from the wall, since the screws that secure the required part are located on the back side. If possible, it is better to move it out of the narrow bathroom altogether.

You cannot spin the washing machine if it is connected to the network. To begin with, it must be de-energized. Then the device is disconnected from communications by turning off the water supply tap and pulling out the drain hose from the sewer. This is done to make it convenient to unfold the machine.

No special tools are needed for the job. A Phillips screwdriver is enough. You also need to prepare a rag. If the machine has been standing in the bathroom for a long time, dust has accumulated in it and will fly to the floor.

Removing a structural element

LG washing machines with vertical and horizontal loading have different designs. To remove the cover from them, you need to adhere to a certain algorithm of actions.

From a horizontal loading washing machine

To remove the top cover from an LG front-loading washing machine, proceed as follows:

find the screws located on the back of the device - there can be two or three of them, the exact number depends on the model of the device;
use a screwdriver to unscrew the screws, turning them counterclockwise;
remove the screws to the side;
Grasping the lid with both hands, gently pull it towards you - if it does not give in, you need to make an effort;
when the lid moves 2-3 cm to the side, it is lifted up and removed.

If the control panel is subsequently removed along with the cover, the process must be recorded on camera. This will make reassembly easier after the repair work is completed.

Under the lid of your LG washing machine there are important parts that need to be handled with care. After removing it, you can repair the following elements:

filling valve. It is responsible for supplying water to the device and is located in the corner of the body.
Detergent tray. Powder is poured into it and conditioner is poured.
Pressostat. This small sensor with a tube is responsible for monitoring the water level. If it fails, replacing it yourself is easy. The main thing is to remove the cover.
Network filter. It protects electronics from power surges. Without a filter, the machine quickly breaks down, as impulses and interference periodically appear in the network. Filter failure does not happen often, but it is not impossible.
Upper counterweight. It is necessary to suppress vibrations. The counterweight cannot break, but it is removed if you need to disassemble the washing machine body.

After dismantling the cover, it will be possible to detect wires that may be broken or have other mechanical damage. Disassembling a washing machine always begins with dismantling the top panel, since important fasteners are located underneath it.

The video will show you how to remove the top cover from an LG washing machine:

From vertical

To remove the cover from an LG top-loading washing machine, you will have to remove the control panel housing. The fact is that it is attached to its surface. The lid itself is also a hatch door.

Procedure:

Unscrew the screws that secure the control module. Most often there are no more than two.
Disconnect the control panel by pulling the wires out of the connectors.
Under the panel you can find bolts that hold the movable part of the cover.
Unscrew the screws and remove the cover.

If the case cannot be disassembled without using sharp tools, you can carefully pry it off with a screwdriver.

To avoid scratching the part, you should use a little trick - wrap the tool several times with tape. It will cover the corners, so the washing machine will remain undamaged.

How to put it back?

The process of installing the lid of an LG washing machine is simple. It is enough to perform all the steps in reverse order.

foto37029-2 Quick Guide:

wipe the cover from dust, remove dirt from the screw holes;
install the part on the body, pressing it with your hands;
move it away from you so that it falls into place;
screw in the screws.

When the cover is in place, the machine is installed back, after which communications and electricity are connected.

Possible difficulties

Sometimes, after tightening the bolts, it is not possible to remove the cover, even with some effort. This indicates that it is jammed. Do not try to pry it off with a screwdriver or other sharp object.. With their help, you can damage the panel: scratch it or leave chips on it.

To remove the upper part of the case, it is enough to perform a few rocking movements from side to side. They should be short, without applying force. If everything is done correctly, the cover can be dismantled and will not be damaged.

If the washing machine is built-in or located under the sink, you will have to pull it out. There is no other way to remove the required part.

Before you start moving the device, you need to close the hatch so that you can hear a click. An open door may prevent the free movement of household appliances. There is also a risk of breaking it during short transportation.

Conclusion

It is not difficult to remove the top cover from an LG washing machine yourself. The main thing is not to use force or try to disassemble the device faster. Compliance with these rules will allow you to solve the problem without damaging household appliances.