Instructions for connecting an Electrolux washing machine to communications

After delivering the washing machine home, it must be connected to communications and installed correctly.

Not only the comfort of using the equipment, but also the service life of the expensive device depends on compliance with all requirements. You can cope with the task on your own or seek help from specialists.

In this article we will talk about connecting an Electrolux washing machine to communications.

Preparation

In order to connect an Electrolux washing machine to electricity, sewerage and water supply, you must first prepare - determine the location for the washing machine, the place where it will be inserted into the pipes, and also the connection to the electrical network. The first acquaintance with Electrolux begins with unpacking the product.

Tools and materials

If the floor of the room where the Electrolux washing machine will be located is slippery, you need to purchase rubber pads on the legs or a special mat, which will prevent the device from moving due to vibration during operation.

Uneven surface requires high-quality leveling. You should not place boards or pieces of cardboard under the legs to compensate for the defect.

If preliminary work on preparing the connection to the sewer and connecting to the water supply has been carried out, no special plumbing tools will be needed. It is enough to have a construction level – it is necessary for a smooth installation, and a wrench may come in handy.

You can remove foam packaging, adhesive film and cellophane without using tools. After installing the Electrolux machine in a permanent place, you should align it with the building level, tightening the legs.

Transport bolts

In all Electrolux washing machines the tank is secured with transport bolts. This is necessary so that when moving it does not hang loosely in the case, hitting other parts and the walls of the device itself.

In order to unscrew the bolts, turn the washer with the back wall towards you. After the bolts have been removed, you need to insert special plugs in their place, which are included in the kit.

Choosing an installation location

It is necessary to determine the installation location of the Electrolux washing machine in advance, paying attention to the following points:

• compliance of the dimensions of the washing machine with the free space, especially if the appliance is built-in, or the room is small;
• proximity of communications;
• sufficient free space so that hoses and wires are not pinched;
• the ability to open the door freely and pull out the powder compartment;
• the device should not touch other furniture and devices with its body;
• the floor must be level.

Air circulation under the washing machine body should not be obstructed, for example, by carpets.

How to connect an Electrolux washing machine?

Consider the stages of connecting household appliances:

To electricity

Washing machines Electrolux designed to operate from a power supply with a voltage of 220-230 V, 50 Hz.

The outlet itself must be removed from the meter separately, without the use of extension cords. The maximum load that the network must withstand is 2.2 kW.

If the socket is installed in the bathroom, then you need to choose a model that is designed for wet rooms and has a special lid. The socket must be separate, with an outlet for the machine.

When connecting the device to a common outlet group, there is a possibility of a power outage due to overload when various devices are simultaneously connected to the network. The socket, in accordance with the rules of electrical engineering, must be grounded.

To water supply

Connecting the Electrolux washing machine to the water supply is done using the inlet hose that comes with the kit. One end of it is connected to the water supply distribution, the other to the washing machine.

The hose that connects to the body can be turned in any direction. If its position needs to be adjusted:

1. The nut is loosened a little.
2. Change the position of the hose.
3. Tighten the nut again, securing the position.

If the length of the hose that comes with the kit is not enough, you can install a new hose of longer length.

To the sewer

Connection to sewerage can be done in several ways:

• use a guide to throw the free end of the hose into the bathtub or sink (more often this option is used as a temporary one);
• directly into the drain pipe;
• into the siphon under the sink.

The drain hose must be raised above the tank level to prevent self-draining.

Options for connecting the drain can be seen in the video:

Setup and first launch

First start of the Electrolux washing machine must be carried out taking into account a number of requirements:

1. The drum and powder receptacle should be inspected for foreign objects.
2. It is necessary to check that the device is connected correctly.
3. Open the water supply tap to the washing machine.
4. Pour washing powder intended for automatic machines (100 grams) into the powder receptacle.
5. Select washing mode at 60? C.
6. Close the hatch.
7. Start washing mode.

When performing the first wash, it is necessary to control the operation of the machine and not leave it unattended. This is necessary so that in the event of a leak or other failure, quickly shut off the water supply and eliminate the defect.

If the first launch was successful, subsequent launches can be carried out as normal – with a stash of dirty laundry for washing.

Call the master

In cases where there is no time or opportunity to connect an Electrolux device yourself, calling a specialist from a washing machine service company will help.

It’s easy to find such a company on the Internet by asking the name of your city in the search question.

The cost of connection work depends on the company’s pricing policy, from which the wizard is called, and whether additional actions are needed to insert into the system, etc.

If the master uses his own parts for connection, for example, a new inlet hose, their cost is paid separately.

On average in the capital, connecting a washing machine with the communications disconnected will cost from 1,500 rubles, and connecting a washing machine built into a set will cost from 1,700 rubles. After installation, the technician performs a test run of the work and gives a guarantee for the work performed.

Recommendations

When connecting an Electrolux washing machine The following recommendations may be useful:

1. When installing, you should not use old hoses that have already been used before.
2. The tap that shuts off the water supply to the washing machine should be located within reach and should not require moving furniture.
3. If the voltage in the network is unstable, it may be useful to use a stabilizer and make the connection through it.
4. The water pressure should be from 100 to 1,000 kPa.
5. Some models of washing machines have a remote control function that allows you to remotely influence the operation of the device. To set up this feature, you need to install the application on your My Electrolux Care gadget. It will allow you to monitor the execution of programs remotely.
6. The washing machine is not designed to be connected to hot water.
7. It is necessary to have unobstructed access to the plug and socket in order to quickly turn off the power to the device if necessary.
8. A faulty device should not be used until the defect is eliminated.

Video on the topic of the article

An example of unpacking and installing an Electrolux washing machine is in the video:

Conclusion

Connecting an Electrolux washing machine is a job that you can do yourself or entrust it to specialists.When organizing connections to all systems, you need to act carefully, paying attention to detail.