Simple steps, or how to clean the filter in a Kandy washing machine

All Kandy washing machines are equipped with a filter to collect debris. This small element plays a vital role: it prevents the pump from breaking due to the smallest particles of dust and dirt getting inside.

In order for the machine to drain water normally, the filter must be cleaned periodically. Read the article on how to properly clean the filter in a Kandy washing machine.

When and how often should you clean?

There are specific signals that indicate that it is time to clean the drain filter in your washing machine. The following signs indicate a blockage:

1. The water takes a long time to drain. Accumulated debris will interfere with its natural flow, slowing down the operation of the device as a whole.
2. The washing mode stops and error code E03 appears on the screen.
3. An unpleasant odor emanates from the appliance and clean laundry. Dirt and debris are a breeding ground for germs. By increasing their numbers, they cause acidification of sediments. During the washing process, the smell always transfers to the fabric.
4. Spin does not start. When the filter is clogged, the pump has to work hard. Due to increased loads, it may burn out.

If the machine is working properly, the filter is cleaned once a year as part of preventative treatment.It is recommended to check its condition every 3 months, which will allow you to maintain the performance of the equipment in optimal condition.

Where is the part located in the Candy washing machine?

Kandy front-loading washing machines have a filter located at the bottom of the device, on its front wall.

It is closed with a small lid that protects the part from mechanical damage. To gain access to the filter, the damper must be opened by carefully prying it with your finger or any thin plate.

If necessary, the washing machine can be slightly raised. The location of the filter for Kandy top-loading washing machines is no different. It can also be found in the lower left corner under the false panel.

Preparing for cleaning

Before you start cleaning the filter, need to prepare:

• empty the washing machine drum;
• disconnect the device from electricity - you cannot perform any manipulations with the device connected to the network;
• shut off the water supply;
• turn the machine around so that nothing interferes with unscrewing the filter;
• provide quality lighting - this may require a flashlight.

Instructions

To avoid damaging the washing machine during the cleaning process, you must follow the instructions. The main rule is to do the work slowly and not to use sharp objects.

Tools

To carry out the procedure The following tools and accessories will be required:

• screwdriver or flat knife with a rounded edge;
• a rag and a bucket for collecting water;
• pelvis;
• flashlight.

Preparation

After the machine is de-energized, you can begin to remove the panel. Sometimes you can't open it manually.

In this case You can use a screwdriver or a wide knife, but you need to act carefully so as not to damage the case.

It is necessary to prepare for the fact that even after completely draining the water from the drum, a small amount of it will remain inside the system. Kandy washing machines do not have an emergency hose, so you need to lay a rag on the floor in advance, with which you can carefully collect the water.

Process

How to open the hatch, remove the filter and clean it? Cleaning instructions:

1. Remove the false panel by folding it towards you or sliding it to the left. The direction of movement may vary depending on the model of the washing machine.
2. Unscrew the filter and wait until the water is completely drained. It will fall on a pre-prepared rag.
3. The drain filter plug in some Candy machines is secured with a special screw. For example, it is found in Kandy Holiday appliances. First you need to loosen it and then completely unscrew it with a screwdriver.
4. Remove the filter. Clean it of large debris: wool, threads and other foreign objects.
5. Use a dish sponge to remove limescale from the filter.
6. Rinse the part under running water. It should not be too hot, as under the influence of boiling water the plastic may be deformed and the rubber seal will lose its shape.
7. The hole in the washing machine in which the filter is located must also be cleaned of debris and wiped off dirt with a damp cloth.
8. Shine a flashlight through the drain pump; if debris is visible in the pump, it must also be removed.
9. Carefully rotate the impeller; nothing should interfere with its rotation.
10. Place the filter in its original position, tighten the fixing bolt, and close the lid.

Sometimes difficulties arise at the stage of removing the filter. Hair, dust and other foreign objects fall into the catcher, blocking its play. Less commonly, the cause of part stoppage is scale on the threads.If you can’t handle it on your own, you need to call a professional.

The video will show you how to clean the filter in a Kandy washing machine:

How to check the performance of a household appliance after?

After the filter has been cleaned and reinstalled, it is necessary to check the functionality of the system as a whole. This is done so that after the first start-up, water does not leak onto the floor, which can happen if the filter is not tightly screwed on.

To check, you need to select the “rinse” program. While performing this mode, you need to make sure that the machine does not leak. If everything is dry, then the hatch can be closed and you can continue to use the device as usual.

Conclusion

Cleaning the drain filter in a Kandy washing machine is a simple task that can be completed even without special knowledge. The whole process will not take more than half an hour, and Thanks to regular maintenance, household appliances will work properly for many years.